3-5174682-7 TE Connectivity, 3-5174682-7 Datasheet
3-5174682-7
Specifications of 3-5174682-7
Available stocks
Related parts for 3-5174682-7
3-5174682-7 Summary of contents
Page 1
... X-5174207-X X-5174214-X X-5174215-X X-5174216-X X-5174217-X X-5174218-X X-5174681-X X-5174682-X X-5174683-X X-5174684-X X-5175710-X X-5175711-X X-5178857-X X-5179359-X O RELEASED FB00-0268-04 DIST LTR REVISION RECORD ASHL-0004-ES REV A Product Specification 108-60036 AMP Connector AMPLIMITE* .050 Series I, Board to Board Lead Free Version Product Descriptions Horizontal Plug Ass’ y Horizontal Cap Ass’ ...
Page 2
... The difference of the thickness of gold-plating is classified by the prefix number, and the contact position is so with the suffix numbers. Fig Type of the Products: The type of the products and their state of application are shown below. Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A PAGE NO 108-60036 2 REV LOC O ES ...
Page 3
... Requirements: 4.1 Structure, Shape and Dimension The product structure, shape and dimensions shall conform to requirements shown on applicable drawing, unless other wise specified below. (1) Number of Positions : 9 type in 20,30,34,40,48,50,60,68 and 96 positions (2) Connector Type: (3) Pitch and Row : (4) Mounting on PCB: Screw-on (M2 Screws) Type (5) Applicable PCB: Board Thickness: 0.8-1.6 mm with solder resistive agent ...
Page 4
... Material and Finish: 4.2.1 Receptacle Contact and post Contact: (1) Material: Phosphor Bronze (2) Finish: Underplating:1.3 µm min. Nickel Underplate all over 4.2.2 Housing: (1) Material : ………………… Fider Glass reinforced (2) Flame Retardancy ……… –0 4.2.3 Retention Leg : (1) Material: … ...
Page 5
... Fig. 6. 30m Measure by applying test potential between the adjacent contacts, and between the contacts and ground in the mated connector. MIL-STD-202, Method 302, Condition B Measure by applying test potential between the adjacent contacts. In the mated connectors. MIL-STD-202, Method 301 108-60036 REV LOC O ES ...
Page 6
... MIL-STD-202, Method 204 Condition A Subject mated connectors to 50 G’s halfsine shock pulses of 11 millisecond duration; 3 shocks in each direction applied along the 3 mutually perpendicular planes total 18 shocks; MIL-STD-202, Method 213 Condition A Using autograph, measure the force required to mate connectors by operating at 100 mm a minute ...
Page 7
... Procedures Mate and unmate connectors for 100 cycles in the same method of testing as Specified in Para 4.6.8,4.6.9. Subject product mounted on printed circuit boards to solder bath at 260 5°C for 3 seconds Subject mated/Unmated connectors to 5 cycles between -55°C and +85°C MIL-STD-202, Method 107 Condition A Subject mated connectors to ...
Page 8
... Product Qualification and Requalification Tests. Test of Examination Examination of Product Termination Resistance, Dry Circuit Dielectric Withstanding Voltage Insulation Resistance Temperature Rise vs. Current Vibration Physical Shock Mating Force Unmating Force Durability Resistance to Soldering Heat Thermal Shock (per Product Spec) Humidity-Temperature Cycling SO2 Gas ...
Page 9
... This drawing applies to horizontal type to horizontal type combination. But horizontal type to vertical type and vertical type to vertical type configurations shall also have their termination resistance measured between tines after installation on circuit boards. Tyco Electronics AMP Shanghai Ltd ASHL-0005- ES REV A : 15~35°C : 45-75% : 86.7~106.7kPa PAGE NO 108-60036 9 REV LOC ...