AD7709ARU Analog Devices Inc, AD7709ARU Datasheet - Page 18

• Manufacturer Part Number: AD7709ARU
• Description: IC ADC 16BIT SIGMA-DELTA 24TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7709ARU

• Mounting Type: Surface Mount
• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Sampling Rate (per Second): 105
• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 3.75mW
• Voltage Supply Source: Single Supply
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-TSSOP (0.173", 4.40mm Width)
• Peak Reflow Compatible (260 C): No
• No. Of Bits: 16 Bit
• Leaded Process Compatible: No
• Features: Switchable Reference Inputs And Current Sources
• No. Of Channels: 2
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD7709
Filter Register (A1, A0 = 1, 0; Power-On-Reset = 45h)
The Filter Register is an 8-bit register from which data can be
read or to which data can be written. This register determines
the amount of averaging performed by the sinc filter. Table VIII
outlines the bit designations for the Filter Register. FR7 through
FR0 indicate the bit location, FR denoting the bits are in the
Filter Register. FR7 denotes the first bit of the data stream. The
number in brackets indicates the power-on/reset default status
of that bit. The number in this register is used to set the decima-
tion factor and thus the output update rate for the ADC. The
Filter Register cannot be written to by the user while the ADC
is active. The update rate is calculated as follows:
where:
Bit
Location
CONFIG3
CONFIG2
CONFIG1
CONFIG0
f
f
SF is the decimal value written to the SF Register.
ADC
MOD
is the ADC output update rate.
is the Modulator Clock Frequency = 32.768 kHz.
f
ADC
=
Bit
Name
UNI
RN2
RN1
RN0
1
3
¥
8
¥
1
S
SF
F
F
Description
Unipolar/Bipolar Operation Selection Bit.
Set by the user to enable unipolar operation. In this mode, the device uses straight binary output coding
i.e., 0 differential input will generate a result of 0000h and a full-scale differential input will generate a
code of FFFFh.
Cleared by the user to enable pseudo-bipolar operation. The device uses offset binary coding, i.e., a nega-
tive full-scale differential input will result in a code of 0000h, a 0 differential input will generate a code of
8000h, while a positive full-scale differential input will result in a code of FFFFh.
This bit is used in conjunction with RN1 and RN0 to select the analog input range as shown below.
This bit is used in conjunction with RN2 and RN0 to select the analog input range as shown below.
This bit is used in conjunction with RN2 and RN1 to select the analog input range as shown below.
R
( 7
RN2
0
0
0
0
1
1
1
1
¥
7
) 0
SF (Dec)
13
69
255
f
MOD
Table VII. Configuration Register Bit Designations (continued)
S
F
F
RN1
0
0
1
1
0
0
1
1
R
( 6
6
) 1
Table VIII. Filter Register Bit Designations
S
Table IX. Update Rate vs. SF WORD
F
F
RN0
0
1
0
1
0
1
0
1
R
( 5
SF (Hex)
0D
45
FF
5
) 0
S
F
F
R
( 4
4
) 0
–18–
Selected ADC Input Range (V
± 20 mV
± 40 mV
± 80 mV
± 160 mV
± 320 mV
± 640 mV
± 1.28 V
± 2.56 V
S
f
105.3
19.79
5.35
The allowable range for SF is 13dec to 255dec. Examples of SF
values and corresponding conversion rate (f
are shown in Table IX. It should also be noted that the ADC
input channel is chopped to minimize offset errors. This means
that the time for a single conversion or the time to the first con-
version result is 2
ADC Data Result Register (A1, A0 = 1, 1; Power-On-Reset =
0000h)
The conversion result is stored in the ADC Data Register (DATA).
This register is 16-bits wide. This is a read-only register. On
completion of a read from this register, the RDY bit in the
Status Register is cleared.
ADC
F
F
R
( 3
3
) 0
(Hz)
S
F
F
R
( 2
2
) 1
t
9.52
50.34
186.77
ADC
t
ADC
S
F
F
(ms)
R
( 1
.
1
) 0
REF
= 2.5 V)
S
F
F
R
( 0
0
) 1
ADC
) and time (t
REV. A
ADC
)