AD5232BRU50-REEL7 Analog Devices Inc, AD5232BRU50-REEL7 Datasheet - Page 8

• Manufacturer Part Number: AD5232BRU50-REEL7
• Description: IC DGTL POT DUAL 256POS 16-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD5232BRU50-REEL7

• Rohs Status: RoHS non-compliant
• Taps: 256
• Resistance (ohms): 50K
• Number Of Circuits: 2
• Temperature Coefficient: 600 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: 4-Wire SPI Serial
• Voltage - Supply: 2.7 V ~ 5.5 V, ±2.25 V ~ 2.75 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP
• Resistance In Ohms: 50K
• Number Of Elements: 2
• # Of Taps: 256
• Resistance (max): 50KOhm
• Power Supply Requirement: Single/Dual
• Interface Type: Serial (4-Wire/SPI)
• Single Supply Voltage (typ): 3/5V
• Dual Supply Voltage (typ): ±2.5V
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): ±2.25V
• Dual Supply Voltage (max): ±2.75V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• For Use With: EVAL-AD5232-10EBZ - BOARD EVALUATION FOR AD5232-10
• Lead Free Status / RoHS Status: Not Compliant

AD5232
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Table 5. Pin Function Descriptions
Pin
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Mnemonic
CLK
SDI
SDO
GND
V
A1
W1
B1
B2
W2
A2
V
WP
PR
CS
RDY
SS
DD
Description
Serial Input Register Clock. Shifts in one bit at a time on positive clock edges.
Serial Data Input. The MSB is loaded first.
Serial Data Output. This open-drain output requires an external pull-up resistor. Command Instruction 9 and Command
Instruction 10 activate the SDO output (see Table 8). Other commands shift out the previously loaded SDI bit pattern
delayed by 16 clock pulses, allowing daisy-chain operation of multiple packages.
Ground, Logic Ground Reference.
Negative Power Supply. Connect to 0 V for single-supply applications.
Terminal A of RDAC1.
Wiper Terminal W of RDAC1, ADDR (RDAC1) = 0x0.
Terminal B of RDAC1.
Terminal B of RDAC2.
Wiper Terminal W of RDAC2, ADDR (RDAC2) = 0x1.
Terminal A of RDAC2.
Positive Power Supply.
Write Protect. When active low, WP prevents any changes to the present register contents, except PR, Command
Instruction 1, and Command Instruction 8, which refresh the RDACx register from EEMEM. Execute an NOP instruction
(Command Instruction 0) before returning WP to logic high.
Hardware Override Preset. Refreshes the scratch pad register with current contents of the EEMEMx register. Factory
default loads Midscale 0x80 until EEMEMx is loaded with a new value by the user (PR is activated at the logic high
transition).
Serial Register Chip Select, Active Low. Serial register operation takes place when CS returns to logic high.
Ready. This active-high, open-drain output requires a pull-up resistor. Identifies completion of Command Instruction 2,
Command Instruction 3, Command Instruction 8, Command Instruction 9, Command Instruction 10, and PR.
GND
SDO
CLK
V
SDI
W1
A1
B1
SS
Figure 4. Pin Configuration
1
4
5
2
3
6
7
8
Rev. A | Page 8 of 24
(Not to Scale)
AD5232
TOP VIEW
16
14
15
13
12
11
10
9
RDY
CS
PR
WP
V
A2
W2
B2
DD