AD5300BRMZ Analog Devices Inc, AD5300BRMZ Datasheet - Page 9

IC DAC 8BIT R-R 2.7-5.5V 8-MSOP

AD5300BRMZ

Manufacturer Part Number
AD5300BRMZ
Description
IC DAC 8BIT R-R 2.7-5.5V 8-MSOP
Manufacturer
Analog Devices Inc
Datasheets

Specifications of AD5300BRMZ

Data Interface
Serial
Settling Time
4µs
Number Of Bits
8
Number Of Converters
1
Voltage Supply Source
Single Supply
Power Dissipation (max)
1.4mW
Operating Temperature
-40°C ~ 105°C
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Resolution (bits)
8bit
Sampling Rate
250kSPS
Input Channel Type
Serial
Supply Voltage Range - Analog
2.7V To 5.5V
Supply Current
140µA
Digital Ic Case Style
SOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AD5300BRMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
SYNC Interrupt
In a normal write sequence, the SYNC line is kept low for at
least 16 falling edges of SCLK and the DAC is updated on the
16th falling edge. However, if SYNC is brought high before the
16th falling edge, this acts as an interrupt to the write sequence.
The shift register is reset and the write sequence is seen as
invalid; neither an update of the DAC register contents or a
change in the operating mode occurs—see Figure 23.
Power-On Reset
The AD5300 contains a power-on reset circuit that controls the
output voltage during power-up. The DAC register is filled with
zeros and the output voltage is 0 V. It remains there until
a valid write sequence is made to the DAC. This is useful in
applications where it is important to know the state of the out-
put of the DAC while it is in the process of powering up.
Power-Down Modes
The AD5300 contains four separate modes of operation. These
modes are software programmable by setting two bits (DB13
and DB12) in the control register. Table I shows how the state
of the bits corresponds to the mode of operation of the device.
DB13
0
0
1
1
When both bits are set to 0, the part works normally with its
normal power consumption of 140 µA at 5 V. However, for the
three power-down modes, the supply current falls to 200 nA at
5 V (50 nA at 3 V). Not only does the supply current fall but
the output stage is also internally switched from the output of
the amplifier to a resistor network of known values. This has an
advantage: the output impedance of the part is known while the
part is in power-down mode. There are three different options.
The output is connected internally to GND through a 1 kΩ resis-
tor or a 100 kΩ resistor, or it is left open-circuited (three-stated).
The output stage is illustrated in Figure 24.
REV.
D
SYNC
SCLK
DIN
Table I. Modes of Operation for the AD5300
SYNC HIGH BEFORE 16
DB12
0
1
0
1
DB15
INVALID WRITE SEQUENCE:
TH
FALLING EDGE
Operating Mode
Normal Operation
Power-Down Modes
1 kΩ to GND
100 kΩ to GND
Three-State
DB0
Figure 23. SYNC Interrupt Facility
–9–
The bias generator, the output amplifier, the resistor string, and
other associated linear circuitry are all shut down when the
power-down mode is activated. However, the contents of the
DAC register are unaffected when in power-down. The time to
exit power-down is typically 2.5 µs for V
V
MICROPROCESSOR INTERFACING
AD5300 to ADSP-2101/ADSP-2103 Interface
Figure 25 shows a serial interface between the AD5300 and the
ADSP-2101/ADSP-2103. The ADSP-2101/ADSP-2103 should
be set up to operate in the SPORT transmit alternate framing
mode. The ADSP-2101/ADSP-2103 SPORT is programmed
through the SPORT control register and should be configured
as follows: internal clock operation, active low framing, 16-bit
word length. Transmission is initiated by writing a word to the
Tx register after the SPORT has been enabled.
DD
Figure 25. AD5300 to ADSP-2101/ADSP-2103 Interface
= 3 V (see Figure 18).
*ADDITIONAL PINS OMITTED FOR CLARITY
VALID WRITE SEQUENCE, OUTPUT UPDATES
Figure 24. Output Stage During Power-Down
ADSP-2103*
STRING DAC
ADSP-2101/
RESISTOR
DB15
ON THE 16
SCLK
TFS
DT
TH
FALLING EDGE
POWER-DOWN
AMPLIFIER
CIRCUITRY
DB0
DD
NETWORK
RESISTOR
DIN
SCLK
SYNC
= 5 V and 5 µs for
AD5300*
AD5300
V
OUT

Related parts for AD5300BRMZ