EP2C5F256C8 Altera, EP2C5F256C8 Datasheet - Page 80

• Manufacturer Part Number: EP2C5F256C8
• Description: IC CYCLONE II FPGA 5K 256-FBGA
• Manufacturer: Altera
• Series: Cyclone® IIr

Specifications of EP2C5F256C8

• Number Of Logic Elements/cells: 4608
• Number Of Labs/clbs: 288
• Total Ram Bits: 119808
• Number Of I /o: 158
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 256-FBGA
• Family Name: Cyclone® II
• Number Of Logic Blocks/elements: 4608
• # I/os (max): 158
• Frequency (max): 402.58MHz
• Process Technology: 90nm
• Operating Supply Voltage (typ): 1.2V
• Logic Cells: 4608
• Ram Bits: 119808
• Operating Supply Voltage (min): 1.15V
• Operating Supply Voltage (max): 1.25V
• Operating Temp Range: 0C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 256
• Package Type: FBGA
• No. Of Macrocells: 4608
• Family Type: Cyclone II
• No. Of I/o's: 158
• Clock Management: PLL
• I/o Supply Voltage: 3.6V
• Operating Frequency Max: 320MHz
• Rohs Compliant: No
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Number Of Gates: -
• Lead Free Status / Rohs Status: Not Compliant
• Other names: 544-1446

Configuration Schemes
Configuration
Schemes
3–6
Cyclone II Device Handbook, Volume 1
Active serial (AS)
Passive serial (PS) Enhanced or EPC2 configuration device, MasterBlaster, ByteBlasterMV, ByteBlaster II or
JTAG
Table 3–4. Data Sources for Configuration
Configuration
Scheme
f
Low-cost serial configuration device
USB Blaster download cable, or serial data source
microprocessor with a Jam or JBC file
MasterBlaster, ByteBlasterMV, ByteBlaster II or USB Blaster download cable or a
SRAM configuration elements allow Cyclone II devices to be
reconfigured in-circuit by loading new configuration data into the device.
With real-time reconfiguration, the device is forced into command mode
with the nCONFIG pin. The configuration process loads different
configuration data, reinitializes the device, and resumes user-mode
operation. You can perform in-field upgrades by distributing new
configuration files within the system or remotely.
A built-in weak pull-up resistor pulls all user I/O pins to V
and during device configuration.
The configuration pins support 1.5-V/1.8-V or 2.5-V/3.3-V I/O
standards. The voltage level of the configuration output pins is
determined by the V
V
3.3-V compatible.
You can load the configuration data for a Cyclone II device with one of
three configuration schemes (see
target application. You can use a configuration device, intelligent
controller, or the JTAG port to configure a Cyclone II device. A low-cost
configuration device can automatically configure a Cyclone II device at
system power-up.
Multiple Cyclone II devices can be configured in any of the three
configuration schemes by connecting the configuration enable (nCE) and
configuration enable output (nCEO) pins on each device.
For more information on configuration, see the Configuring Cyclone II
Devices chapter of the Cyclone II Handbook, Volume 2.
CCIO
selects whether the configuration inputs are 1.5-V, 1.8-V, 2.5-V, or
CCIO
of the bank where the pins reside. The bank
Data Source
Table
3–4), chosen on the basis of the
Altera Corporation
February 2007
CCIO
before