EP1C12Q240C8 Altera, EP1C12Q240C8 Datasheet - Page 44
![IC CYCLONE FPGA 12K LE 240-PQFP](/photos/6/72/67260/544-240-pqfp_sml.jpg)
EP1C12Q240C8
Manufacturer Part Number
EP1C12Q240C8
Description
IC CYCLONE FPGA 12K LE 240-PQFP
Manufacturer
Altera
Series
Cyclone®r
Datasheet
1.EP1C3T144C8.pdf
(106 pages)
Specifications of EP1C12Q240C8
Number Of Logic Elements/cells
12060
Number Of Labs/clbs
1206
Total Ram Bits
239616
Number Of I /o
173
Voltage - Supply
1.425 V ~ 1.575 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
240-MQFP, 240-PQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Other names
544-1081
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP1C12Q240C8
Manufacturer:
ALTERA
Quantity:
67
Company:
Part Number:
EP1C12Q240C8
Manufacturer:
XILINX
Quantity:
5
Part Number:
EP1C12Q240C8
Manufacturer:
ALTERA
Quantity:
20 000
Company:
Part Number:
EP1C12Q240C8N
Manufacturer:
APTINA
Quantity:
3 000
Company:
Part Number:
EP1C12Q240C8N
Manufacturer:
ALTERA
Quantity:
99
Company:
Part Number:
EP1C12Q240C8N
Manufacturer:
ALTERA
Quantity:
348
Part Number:
EP1C12Q240C8N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Cyclone Device Handbook, Volume 1
2–38
Preliminary
f
Programmable Duty Cycle
The programmable duty cycle allows PLLs to generate clock outputs with
a variable duty cycle. This feature is supported on each PLL post-scale
counter (g0, g1, e). The duty cycle setting is achieved by a low- and
high-time count setting for the post-scale dividers. The Quartus II
software uses the frequency input and the required multiply or divide
rate to determine the duty cycle choices.
Control Signals
There are three control signals for clearing and enabling PLLs and their
outputs. You can use these signals to control PLL resynchronization and
the ability to gate PLL output clocks for low-power applications.
The pllenable signal enables and disables PLLs. When the pllenable
signal is low, the clock output ports are driven by ground and all the PLLs
go out of lock. When the pllenable signal goes high again, the PLLs
relock and resynchronize to the input clocks. An input pin or LE output
can drive the pllenable signal.
The areset signals are reset/resynchronization inputs for each PLL.
Cyclone devices can drive these input signals from input pins or from
LEs. When areset is driven high, the PLL counters will reset, clearing
the PLL output and placing the PLL out of lock. When driven low again,
the PLL will resynchronize to its input as it relocks.
The pfdena signals control the phase frequency detector (PFD) output
with a programmable gate. If you disable the PFD, the VCO will operate
at its last set value of control voltage and frequency with some drift, and
the system will continue running when the PLL goes out of lock or the
input clock disables. By maintaining the last locked frequency, the system
has time to store its current settings before shutting down. You can either
use their own control signal or gated locked status signals to trigger the
pfdena signal.
For more information about Cyclone PLLs, refer to
Devices
chapter in the Cyclone Device Handbook.
Using PLLs in Cyclone
Altera Corporation
May 2008