EP1C12Q240C8 Altera, EP1C12Q240C8 Datasheet - Page 68
![IC CYCLONE FPGA 12K LE 240-PQFP](/photos/6/72/67260/544-240-pqfp_sml.jpg)
EP1C12Q240C8
Manufacturer Part Number
EP1C12Q240C8
Description
IC CYCLONE FPGA 12K LE 240-PQFP
Manufacturer
Altera
Series
Cyclone®r
Datasheet
1.EP1C3T144C8.pdf
(106 pages)
Specifications of EP1C12Q240C8
Number Of Logic Elements/cells
12060
Number Of Labs/clbs
1206
Total Ram Bits
239616
Number Of I /o
173
Voltage - Supply
1.425 V ~ 1.575 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
240-MQFP, 240-PQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Other names
544-1081
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP1C12Q240C8
Manufacturer:
ALTERA
Quantity:
67
Company:
Part Number:
EP1C12Q240C8
Manufacturer:
XILINX
Quantity:
5
Part Number:
EP1C12Q240C8
Manufacturer:
ALTERA
Quantity:
20 000
Company:
Part Number:
EP1C12Q240C8N
Manufacturer:
APTINA
Quantity:
3 000
Company:
Part Number:
EP1C12Q240C8N
Manufacturer:
ALTERA
Quantity:
99
Company:
Part Number:
EP1C12Q240C8N
Manufacturer:
ALTERA
Quantity:
348
Part Number:
EP1C12Q240C8N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Cyclone Device Handbook, Volume 1
3–6
Preliminary
Operating Modes
The Cyclone architecture uses SRAM configuration elements that require
configuration data to be loaded each time the circuit powers up. The
process of physically loading the SRAM data into the device is called
configuration. During initialization, which occurs immediately after
configuration, the device resets registers, enables I/O pins, and begins to
operate as a logic device. Together, the configuration and initialization
processes are called command mode. Normal device operation is called
user mode.
SRAM configuration elements allow Cyclone devices to be reconfigured
in-circuit by loading new configuration data into the device. With real-
time reconfiguration, the device is forced into command mode with a
device pin. The configuration process loads different configuration data,
reinitializes the device, and resumes user-mode operation. Designers can
perform in-field upgrades by distributing new configuration files either
within the system or remotely.
A built-in weak pull-up resistor pulls all user I/O pins to V
and during device configuration.
The configuration pins support 1.5-V/1.8-V or 2.5-V/3.3-V I/O
standards. The voltage level of the configuration output pins is
determined by the V
V
3.3-V compatible.
Configuration Schemes
Designers can load the configuration data for a Cyclone device with one
of three configuration schemes (see
target application. Designers can use a configuration device, intelligent
controller, or the JTAG port to configure a Cyclone device. A low-cost
configuration device can automatically configure a Cyclone device at
system power-up.
CCIO
selects whether the configuration inputs are 1.5-V, 1.8-V, 2.5-V, or
CCIO
of the bank where the pins reside. The bank
Table
3–5), chosen on the basis of the
Altera Corporation
CCIO
May 2008
before