EP3C16F484C8N Altera, EP3C16F484C8N Datasheet - Page 218
![IC CYCLONE III FPGA 16K 484FBGA](/photos/6/72/67258/544-484-fbga_sml.jpg)
EP3C16F484C8N
Manufacturer Part Number
EP3C16F484C8N
Description
IC CYCLONE III FPGA 16K 484FBGA
Manufacturer
Altera
Series
Cyclone® IIIr
Datasheets
1.EP3C5F256C8N.pdf
(5 pages)
2.EP3C5F256C8N.pdf
(34 pages)
3.EP3C5F256C8N.pdf
(66 pages)
4.EP3C5F256C8N.pdf
(14 pages)
5.EP3C5F256C8N.pdf
(76 pages)
6.EP3C10M164C8N.pdf
(350 pages)
7.EP3C16F484C8N.pdf
(274 pages)
Specifications of EP3C16F484C8N
Number Of Logic Elements/cells
15408
Number Of Labs/clbs
963
Total Ram Bits
516096
Number Of I /o
346
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
484-FBGA
Family Name
Cyclone III
Number Of Logic Blocks/elements
15408
# I/os (max)
346
Frequency (max)
402MHz
Process Technology
65nm
Operating Supply Voltage (typ)
1.2V
Logic Cells
15408
Ram Bits
516096
Operating Supply Voltage (min)
1.15V
Operating Supply Voltage (max)
1.25V
Operating Temp Range
0C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
484
Package Type
FBGA
No. Of Logic Blocks
963
Family Type
Cyclone III
No. Of I/o's
346
I/o Supply Voltage
3.3V
Operating Frequency Max
402MHz
Operating Temperature Range
0°C To +85°C
Rohs Compliant
Yes
For Use With
544-2601 - KIT DEV CYCLONE III LS EP3CLS200P0037 - BOARD DEV/EDUCATION ALTERA DE0544-2411 - KIT DEV NIOS II CYCLONE III ED.
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Gates
-
Lead Free Status / Rohs Status
Compliant
Other names
544-2474
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP3C16F484C8N
Manufacturer:
ALTERA
Quantity:
331
Company:
Part Number:
EP3C16F484C8N
Manufacturer:
ALTERA44
Quantity:
120
Part Number:
EP3C16F484C8N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
9–58
Cyclone III Device Handbook, Volume 1
Figure 9–29. Combining JTAG and AS Configuration Schemes
Notes to
(1) Connect these pull-up resistors to the V
(2) Power up the V
(3) Pin 6 of the header is a V
(4) The MSEL pin settings vary for different configuration voltage standards and POR time. To connect MSEL[3..0]for
(5) These are dual-purpose I/O pins. This nCSO pin functions as the FLASH_NCE pin in AP mode. The ASDO pin
(6) Power up V
(7) You must place the diodes and capacitors as close as possible to the Cyclone III device family. For effective voltage
device. For this value, refer to the
this pin is a no connect. In USB-Blaster and ByteBlaster II, this pin is connected to nCE when it is used for AS
programming, otherwise it is a no connect.
AS configuration schemes, refer to
functions as the DATA[1] pin in other AP and FPP modes.
V
cable. The MasterBlaster cable can receive power from either 5.0- or 3.3-V circuit boards, DC power supply, or 5.0 V
from the USB cable. For this value, refer to the
clamping, Altera recommends using the Schottky diode, which has a relatively lower forward diode voltage (VF) than
the switching and Zener diodes. For more information about the interface guidelines using Schottky diodes, refer to
AN 523: Cyclone III Configuration Interface Guidelines with EPCS Devices.
CCA
10-Pin Male Header
Download Cable
. Third-party programmers must switch to 2.5 V. Pin 4 of the header is a V
Figure
Chapter 9: Configuration, Design Security, and Remote System Upgrades in the Cyclone III Device Family
Configuration
(AS Mode)
Pin 1
Device
Serial
CC
DCLK
DATA
ASDI
9–29:
nCS
of the ByteBlaster II, USB-Blaster, ByteBlasterMV, or Ethernet Blaster cable with a 2.5- V supply from
3.3 V (2)
CC
10 kΩ
10kΩ
of the ByteBlaster II, USB-Blaster, or Ethernet Blaster cable with the 3.3-V supply.
V
CCIO
GND
IO
(1)
10 kΩ
reference voltage for the MasterBlaster output driver. V
V
10 pf
(7)
CCIO
(7)
GND
MasterBlaster Serial/USB Communications Cable User
3.3 V
(1)
10 kΩ
Table 9–7 on page
GND
3.3 V
V
CCIO
CCIO
GND
3.3 V
10 pf
supply of the bank in which the pin resides.
(1)
10 pf
3.3 V
MasterBlaster Serial/USB Communications Cable User
GND
Cyclone III Device Family
nSTATUS
CONF_DONE
nCONFIG
nCE
DATA[0]
DCLK
nCSO (5)
ASDO (5)
9–11. Connect the MSEL pins directly to V
10 pf
MSEL [3..0]
nCEO
TCK
TDO
TMS
TDI
© December 2009 Altera Corporation
N.C.
(4)
CC
V
power supply for the MasterBlaster
CCA
IO
must match the V
10 kΩ
V
1 kΩ
CCA
Guide. In ByteBlasterMV,
10 kΩ
GND
Configuration Features
10-Pin Male Header
Pin 1
Download Cable
CCA
(JTAG Mode)
(top view)
or GND.
Guide.
CCA
V
of the
CCA
V
IO
(6)
(3)