EP3C16F484C8N Altera, EP3C16F484C8N Datasheet - Page 3
![IC CYCLONE III FPGA 16K 484FBGA](/photos/6/72/67258/544-484-fbga_sml.jpg)
EP3C16F484C8N
Manufacturer Part Number
EP3C16F484C8N
Description
IC CYCLONE III FPGA 16K 484FBGA
Manufacturer
Altera
Series
Cyclone® IIIr
Datasheets
1.EP3C5F256C8N.pdf
(5 pages)
2.EP3C5F256C8N.pdf
(34 pages)
3.EP3C5F256C8N.pdf
(66 pages)
4.EP3C5F256C8N.pdf
(14 pages)
5.EP3C5F256C8N.pdf
(76 pages)
6.EP3C10M164C8N.pdf
(350 pages)
7.EP3C16F484C8N.pdf
(274 pages)
Specifications of EP3C16F484C8N
Number Of Logic Elements/cells
15408
Number Of Labs/clbs
963
Total Ram Bits
516096
Number Of I /o
346
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
484-FBGA
Family Name
Cyclone III
Number Of Logic Blocks/elements
15408
# I/os (max)
346
Frequency (max)
402MHz
Process Technology
65nm
Operating Supply Voltage (typ)
1.2V
Logic Cells
15408
Ram Bits
516096
Operating Supply Voltage (min)
1.15V
Operating Supply Voltage (max)
1.25V
Operating Temp Range
0C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
484
Package Type
FBGA
No. Of Logic Blocks
963
Family Type
Cyclone III
No. Of I/o's
346
I/o Supply Voltage
3.3V
Operating Frequency Max
402MHz
Operating Temperature Range
0°C To +85°C
Rohs Compliant
Yes
For Use With
544-2601 - KIT DEV CYCLONE III LS EP3CLS200P0037 - BOARD DEV/EDUCATION ALTERA DE0544-2411 - KIT DEV NIOS II CYCLONE III ED.
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Number Of Gates
-
Lead Free Status / Rohs Status
Compliant
Other names
544-2474
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP3C16F484C8N
Manufacturer:
ALTERA
Quantity:
331
Company:
Part Number:
EP3C16F484C8N
Manufacturer:
ALTERA44
Quantity:
120
Part Number:
EP3C16F484C8N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
MSEL Pin Connection
Table 3. Full-Rate DDR2 SDRAM Support for Cyclone III Devices
MSEL Pin Connection
Solution
Configuration Transition Current Issue
© June 2010 Altera Corporation
DDR2 SDRAM
Note to
(1) You must use 267-MHz memory component speed grade when using the Class I I/O standard and a 333-MHz memory component speed grade
(2) You must use a 200-MHz memory component speed grade.
when using the Class II I/O standard.
Table
Memory Standard
3:
1
Both Quartus II version 9.0 and 9.1 specifications refer to the DDR2 SDRAM
AFI-based PHY.
To achieve a higher clock rate in your system, refer to this Solution.
Altera has identified an issue with Cyclone III MSEL pins connected to V
high. If V
the MSEL pins may be sensed at a different setting than was intended. The device
might then require a power cycle to recover. This issue does not occur when the
device is in user mode or when configuration has started.
Connect MSEL pins to V
point then the POR circuit will reset the device. If you have already connected the
MSEL pins to V
recommended operating condition voltage level and stays within the voltage min and
max. A monotonic rise will prevent the issue from occurring.
Cyclone III EP3C25 ES Revision B and C and EP3C120 ES Revision A devices might
exhibit a momentary current surge from the V
system’s V
transition into user mode as intended. This issue will be fixed in all production
devices. While the size of the current surge is dependent on your design and on
Quartus II placement and routing, the following currents are maximums for each
device.
Table 4. Transition Current
CCIO
CCINT
EP3C120
EP3C25
Device
Cyclone III
sags below 0.75 V after power on reset and before configuration starts,
Device
CC IO
supply does not provide this current, the Cyclone III device might not
on your board, make sure that V
CCA
Speed Grade
for a logic high. If V
C8, I7, A7
C6
C7
Peak Current from V
CCINT
CCA
supply after configuration. If your
Maximum Clock Rate (MHz)
sags below the device’s POR trip
CCIO
CCINT
Single Chip Select
600 mA
rises monotonically to its
3 A
Column I/O
Cyclone III Device Family Errata Sheet
Supply During Transition
167
150
150
(1)
(2)
(1)
CCIO
for logic
Page 3