EP2S15F484C4 Altera, EP2S15F484C4 Datasheet - Page 93
![IC STRATIX II FPGA 15K 484-FBGA](/photos/6/72/67258/544-484-fbga_sml.jpg)
EP2S15F484C4
Manufacturer Part Number
EP2S15F484C4
Description
IC STRATIX II FPGA 15K 484-FBGA
Manufacturer
Altera
Series
Stratix® IIr
Datasheet
1.EP2S15F484I4N.pdf
(238 pages)
Specifications of EP2S15F484C4
Number Of Logic Elements/cells
15600
Number Of Labs/clbs
780
Total Ram Bits
419328
Number Of I /o
342
Voltage - Supply
1.15 V ~ 1.25 V
Mounting Type
Surface Mount
Operating Temperature
0°C ~ 85°C
Package / Case
484-FBGA
Family Name
Stratix II
Number Of Logic Blocks/elements
15600
# I/os (max)
342
Frequency (max)
711.24MHz
Process Technology
90nm (CMOS)
Operating Supply Voltage (typ)
1.2V
Logic Cells
15600
Ram Bits
419328
Operating Supply Voltage (min)
1.15V
Operating Supply Voltage (max)
1.25V
Operating Temp Range
0C to 85C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
484
Package Type
FC-FBGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Lead Free Status / Rohs Status
Not Compliant
Other names
544-1104
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP2S15F484C4
Manufacturer:
ALTERA30
Quantity:
146
Part Number:
EP2S15F484C4
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Company:
Part Number:
EP2S15F484C4N
Manufacturer:
ALTERA
Quantity:
325
Part Number:
EP2S15F484C4N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
Altera Corporation
May 2007
The bus-hold circuitry also pulls undriven pins away from the input
threshold voltage where noise can cause unintended high-frequency
switching. You can select this feature individually for each I/O pin. The
bus-hold output drives no higher than V
signals. If the bus-hold feature is enabled, the programmable pull-up
option cannot be used. Disable the bus-hold feature when the I/O pin has
been configured for differential signals.
The bus-hold circuitry uses a resistor with a nominal resistance (R
approximately 7 kΩ to weakly pull the signal level to the last-driven state.
See the DC & Switching Characteristics chapter in the Stratix II Device
Handbook, Volume 1, for the specific sustaining current driven through this
resistor and overdrive current used to identify the next-driven input
level. This information is provided for each V
The bus-hold circuitry is active only after configuration. When going into
user mode, the bus-hold circuit captures the value on the pin present at
the end of configuration.
Programmable Pull-Up Resistor
Each Stratix II device I/O pin provides an optional programmable
pull-up resistor during user mode. If you enable this feature for an I/O
pin, the pull-up resistor (typically 25 kΩ) weakly holds the output to the
V
Programmable pull-up resistors are only supported on user I/O pins, and
are not supported on dedicated configuration pins, JTAG pins or
dedicated clock pins.
Advanced I/O Standard Support
Stratix II device IOEs support the following I/O standards:
■
■
■
■
■
■
■
■
■
■
■
■
■
CCIO
3.3-V LVTTL/LVCMOS
2.5-V LVTTL/LVCMOS
1.8-V LVTTL/LVCMOS
1.5-V LVCMOS
3.3-V PCI
3.3-V PCI-X mode 1
LVDS
LVPECL (on input and output clocks only)
HyperTransport technology
Differential 1.5-V HSTL Class I and II
Differential 1.8-V HSTL Class I and II
Differential SSTL-18 Class I and II
Differential SSTL-2 Class I and II
level of the output pin’s bank.
Stratix II Device Handbook, Volume 1
CCIO
to prevent overdriving
CCIO
voltage level.
Stratix II Architecture
BH
2–85
) of