XC4020E-4HQ208I Xilinx Inc, XC4020E-4HQ208I Datasheet - Page 36

no-image

XC4020E-4HQ208I

Manufacturer Part Number
XC4020E-4HQ208I
Description
IC FPGA I-TEMP 5V 4SPD 208-HQFP
Manufacturer
Xilinx Inc
Series
XC4000E/Xr
Datasheet

Specifications of XC4020E-4HQ208I

Number Of Logic Elements/cells
1862
Number Of Labs/clbs
784
Total Ram Bits
25088
Number Of I /o
160
Number Of Gates
20000
Voltage - Supply
4.5 V ~ 5.5 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
208-BFQFP Exposed Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
XC4020E-4HQ208I
Manufacturer:
XILINX
0
Part Number:
XC4020E-4HQ208I
Manufacturer:
XLINX
Quantity:
5 530
Part Number:
XC4020E-4HQ208I
Manufacturer:
Xilinx Inc
Quantity:
10 000
Part Number:
XC4020E-4HQ208I
Manufacturer:
XILINX
0
XC4000E and XC4000X Series Field Programmable Gate Arrays
Table 16: Pin Descriptions
6-40
Permanently Dedicated Pins
User I/O Pins That Can Have Special Functions
M0, M1, M2
PROGRAM
RDY/BUSY
Pin Name
DONE
CCLK
RCLK
GND
VCC
TDO
Config.
During
I or O
I/O
I/O
O
O
O
I
I
I
I
Product Obsolete or Under Obsolescence
Config.
O (M1),
I (M0),
I (M2)
After
I/O
I/O
I/O
O
O
I
I
I
I
Eight or more (depending on package) connections to the nominal +5 V supply voltage
(+3.3 V for low-voltage devices). All must be connected, and each must be decoupled
with a 0.01 - 0.1 F capacitor to Ground.
Eight or more (depending on package type) connections to Ground. All must be con-
nected.
During configuration, Configuration Clock (CCLK) is an output in Master modes or Asyn-
chronous Peripheral mode, but is an input in Slave mode and Synchronous Peripheral
mode. After configuration, CCLK has a weak pull-up resistor and can be selected as the
Readback Clock. There is no CCLK High or Low time restriction on XC4000 Series de-
vices, except during Readback. See
ification for the Readback Clock” on page 56
DONE is a bidirectional signal with an optional internal pull-up resistor. As an output, it
indicates the completion of the configuration process. As an input, a Low level on DONE
can be configured to delay the global logic initialization and the enabling of outputs.
The optional pull-up resistor is selected as an option in the XACT step program that cre-
ates the configuration bitstream. The resistor is included by default.
PROGRAM is an active Low input that forces the FPGA to clear its configuration mem-
ory. It is used to initiate a configuration cycle. When PROGRAM goes High, the FPGA
finishes the current clear cycle and executes another complete clear cycle, before it
goes into a WAIT state and releases INIT.
The PROGRAM pin has a permanent weak pull-up, so it need not be externally pulled
up to Vcc.
During Peripheral mode configuration, this pin indicates when it is appropriate to write
another byte of data into the FPGA. The same status is also available on D7 in Asyn-
chronous Peripheral mode, if a read operation is performed when the device is selected.
After configuration, RDY/BUSY is a user-programmable I/O pin.
RDY/BUSY is pulled High with a high-impedance pull-up prior to INIT going High.
During Master Parallel configuration, each change on the A0-A17 outputs (A0 - A21 for
XC4000X) is preceded by a rising edge on RCLK, a redundant output signal. RCLK is
useful for clocked PROMs. It is rarely used during configuration. After configuration,
RCLK is a user-programmable I/O pin.
As Mode inputs, these pins are sampled after INIT goes High to determine the configu-
ration mode to be used. After configuration, M0 and M2 can be used as inputs, and M1
can be used as a 3-state output. These three pins have no associated input or output
registers.
During configuration, these pins have weak pull-up resistors. For the most popular con-
figuration mode, Slave Serial, the mode pins can thus be left unconnected. The three
mode inputs can be individually configured with or without weak pull-up or pull-down re-
sistors. A pull-down resistor value of 4.7 k is recommended.
These pins can only be used as inputs or outputs when called out by special schematic
definitions. To use these pins, place the library components MD0, MD1, and MD2 in-
stead of the usual pad symbols. Input or output buffers must still be used.
If boundary scan is used, this pin is the Test Data Output. If boundary scan is not used,
this pin is a 3-state output without a register, after configuration is completed.
This pin can be user output only when called out by special schematic definitions. To
use this pin, place the library component TDO instead of the usual pad symbol. An out-
put buffer must still be used.
Pin Description
“Violating the Maximum High and Low Time Spec-
for an explanation of this exception.
May 14, 1999 (Version 1.6)
R

Related parts for XC4020E-4HQ208I