ATF16V8B-10JU Atmel, ATF16V8B-10JU Datasheet

Page 1

... Each of these options significantly reduces total system power and enhances system reliability. The ATF16V8Bs incorporate a superset of the generic architectures, which allows direct replacement of the 16R8 family and most 20-pin combinatorial PLDs. Eight out- puts are each allocated eight product terms. Three different modes of operation, configured automatically with software, allow highly complex logic functions to be realized ...

Page 2

... Figure 1-1. 2. Pin Configurations Table 2-1. Pin Name CLK I I/O OE VCC Figure 2-1. Figure 2-3. ATF16V8B/BQ/BQL 2 Block Diagram Pin Configurations (All Pinouts Top View) Function Clock Logic Inputs Bi-directional Buffers Output Enable +5V Supply TSSOP I/CLK 1 20 VCC I/O ...

Page 3

... Note: 1. Minimum voltage is -0.6V DC, which may under- shoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is V which may overshoot to 7.0V for pulses of less (1) than 20 ns. Commercial ATF16V8B/BQ/BQL + 0.75V DC, CC Industrial 10% 3 ...

Page 4

... OS Circuit Current V Input Low Voltage IL V Input High Voltage IH V Output High Voltage OL V Output High Voltage OH Note: 1. Not more than one output at a time should be shorted. Duration of short circuit test should not exceed 30 sec. ATF16V8B/BQ/BQL 4 Condition (Max 3 Com. B-10 Ind. ...

Page 5

... PZX t OE pin to Output Disable PXZ Note: 1. See ordering information for valid part numbers and speed grades. 0364J–PLD–7/05 1. Timing measurement reference is 1.5V. Input AC driving levels are 0.0V 3.0V, unless otherwise specified. 8 outputs switching + ATF16V8B/BQ/BQL -10 -15 Min Max Min Max ...

Page 6

... R F 4.4.2 Output Test Loads (Commercial) C includes Test fixture and Probe capacitance L 4.5 Pin Capacitance Table 4- OUT Note: ATF16V8B/BQ/BQL 6 Pin Capacitance ( MHz 25°C Typ Max Typical values for nominal supply voltage. This parameter is only sampled and is not 100% tested. (1) ) Units Conditions ...

Page 7

... Once downloaded, the JEDEC file preload sequence will be done automatically by most of the approved programmers after the programming. 5. Security Fuse Usage A single fuse is provided to prevent unauthorized copying of the ATF16V8B fuse patterns. Once programmed, fuse verify and preload are inhibited. However, the 64-bit User Signature remains accessible. ...

Page 8

... The ATF16V8B can be configured in one of three different modes. Each mode makes the ATF16V8B look like a different device. Most PLD compilers can choose the right mode automat- ically. The user can also force the selection by supplying the compiler with a mode selection. ...

Page 9

... The user can download the listed subset device JEDEC programming file to the PLD programmer, and the ATF16V8B can be configured to act like the chosen device. Check with your programmer manufacturer for this capability. Unused product terms are automatically disabled by the compiler to decrease power consump- tion ...

Page 10

... ATF16V8B Registered Mode PAL Device Emulation/PAL Replacement. The registered mode is used if one or more regis- ters are required. Each macrocell can be configured as either a registered or combinatorial output or I/ input. For a registered output or I/O, the output is enabled by the OE pin, and the register is clocked by the CLK pin. Eight product terms are allocated to the sum term. ...

Page 11

... Figure 11-3. Registered Mode Logic Diagram 0364J–PLD–7/05 ATF16V8B/BQ/BQL 11 ...

Page 12

... ATF16V8B Complex Mode PAL Device Emulation/PAL Replacement. In the complex mode, combinatorial output and I/O functions are possible. Pins 1 and 11 are regular inputs to the array. Pins 13 through 18 have pin feedback paths back to the AND-array, which makes full I/O capability possible. Pins 12 and 19 (outermost macrocells) are outputs only ...

Page 13

... Figure 11-5. Complex Mode Logic Diagram 0364J–PLD–7/05 ATF16V8B/BQ/BQL 13 ...

Page 14

... ATF16V8B Simple Mode PAL Device Emulation/PAL Replacement. In the Simple Mode, 8 product terms are allocated to the sum term. Pins 15 and 16 (center macrocells) are permanently configured as combinato- rial outputs. Other macrocells can be either inputs or combinatorial outputs with pin feedback to the AND-array. Pins 1 and 11 are regular inputs. ...

Page 15

... Figure 11-7. Simple Mode Logic Diagram 0364J–PLD–7/05 ATF16V8B/BQ/BQL 15 ...

Page 16

... Test Characterization Data SUPPLY CURRENT vs. INPUT FREQUENCY ATF16V8B/BQ (VCC = 5V 25C FREQUENCY (MHz) SUPPLY CURRENT vs. SUPPLY VOLTAGE ATF16V8B/BQ (TA = 25C 4.50 4.75 5.00 SUPPLY VOLTAGE (V) OUTPUT SOURCE CURRENT vs. SUPPLY VOLTAGE (TA = 25C) -10 -12 I -14 O -16 H -18 m -20 A -22 -24 4.5 4.7 4.9 SUPPLY VOLTAGE (V) ATF16V8B/BQ/BQL ...

Page 17

... NORMALIZED TPD vs. SUPPLY VOLTAGE (TA=25° 0.85 D 0.7 4.50 4.75 5.00 SUPPLY VOLTAGE (V) NORMALIZED TCO vs. SUPPLY VOLTAGE(TA=25°C) 1 0.7 4.50 4.75 5.00 SUPPLY VOLT AGE (V) 0364J–PLD–7/05 ATF16V8B/BQ ATF16V8BQL 5.25 5.50 ATF16V8B/BQ ATF16V8BQL 5.25 5.50 ATF16V8B/BQ/BQL 17 ...

Page 18

... ATF16V8B/BQ/BQL 18 0364J–PLD–7/05 ...

Page 19

... Ordering Code Package ATF16V8B-10JC ATF16V8B-10PC ATF16V8B-10SC ATF16V8B-10XC ATF16V8B-10JI ATF16V8B-10PI ATF16V8B-10SI ATF16V8B-10XI ATF16V8B-15JC ATF16V8B-15PC ATF16V8B-15SC ATF16V8B-15XC ATF16V8B-15JI ATF16V8B-15PI ATF16V8B-15SI ATF16V8B-15XI Ordering Code Package ATF16V8B-10JU ATF16V8B-15JU ATF16V8B-15PU ATF16V8B-15SU ATF16V8B-15XU Package Type ATF16V8B/BQ/BQL Operation Range 20J 20P3 Commercial 20S ( 20X 20J 20P3 Industrial 20S (- 20X ...

Page 20

... (ns) (ns) (ns Note: The last time buy date is Sept. 30, 2005 for shaded parts. 14.2 ATF16V8BQ and ATF16V8BQL Green Package Options (Pb/Halide-free/RoHS Compliant (ns) (ns) (ns 14.3 Using “C” Product for Industrial To use commercial product for Industrial temperature ranges, down-grade one speed grade from the “ ...

Page 21

... Lead coplanarity is 0.004" (0.102 mm) maximum. 2325 Orchard Parkway San Jose, CA 95131 R 0364J–PLD–7/05 PIN NO. 1 1.14(0.045) X 45˚ IDENTIFIER TITLE 20J, 20-lead, Plastic J-leaded Chip Carrier (PLCC) ATF16V8B/BQ/BQL 0.318(0.0125) 0.191(0.0075) D2/ COMMON DIMENSIONS (Unit of Measure = mm) MIN NOM MAX SYMBOL A 4.191 – ...

Page 22

... A SEATING PLANE Notes: 1. This package conforms to JEDEC reference MS-001, Variation AD. 2. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010"). 2325 Orchard Parkway San Jose, CA 95131 R ATF16V8B/BQ/BQL 22 D PIN TITLE 20P3, 20-lead (0.300"/7.62 mm Wide) Plastic Dual ...

Page 23

... TITLE 20S, 20-lead, 0.300" Body, Plastic Gull Wing Small Outline (SOIC) ATF16V8B/BQ/BQL 7.60 (0.2992) 10.65 (0.419) 10.00 (0.394) 7.40 (0.2914) 2.65 (0.1043) 2.35 (0.0926) 0.32 (0.0125) 0.23 (0.0091) DRAWING NO ...

Page 24

... TSSOP Dimensions in Millimeters and (Inches). Controlling dimension: Millimeters. JEDEC Standard MO-153 AC 0.65 (.0256) BSC 0º ~ 8º 2325 Orchard Parkway San Jose, CA 95131 R ATF16V8B/BQ/BQL 24 PIN 1 4.50 (0.177) 4.30 (0.169) 6.60 (.260) 6.40 (.252) 0.15 (0.006) 0.30 (0.012) 0.05 (0.002) ...

Page 25

... Revision History 16.1 0364J 1. ATF16V8B-25 JC/PC/SC/XC/JI/PI/SI/XI were obseleted in August 1999 ATF16V8BQL-25 JC/PC/SC/XC/JI/PI/SI/XI were obseleted in August 1999 These devices were removed from page 19 2. Green Package options added in 2005. 0364J–PLD–7/05 Section 13. ”ATF16V8B Ordering Information” on and Section 14. ”ATF16V8BQ/BQL Ordering Information” on page ATF16V8B/BQ/BQL 20 ...

Page 26

... Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN ATMEL’S TERMS AND CONDI- TIONS OF SALE LOCATED ON ATMEL’S WEB SITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT ...