AD51/067ARMZ-2RL ON Semiconductor, AD51/067ARMZ-2RL Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
AD51/067ARMZ-2RL
Manufacturer Part Number
AD51/067ARMZ-2RL
Description
Board Mount Temperature Sensors TEMP MONITR DUAL CHN W/SERIES RSTNCE CNCL
Manufacturer
ON Semiconductor
Datasheet
1.AD51067ARMZ-2RL.pdf
(20 pages)
Specifications of AD51/067ARMZ-2RL
Full Temp Accuracy
+/- 1 C, +/- 3 C
Package / Case
MSOP
Digital Output - Bus Interface
Serial (2-Wire)
Maximum Operating Temperature
+ 127 C
Minimum Operating Temperature
0 C
Output Type
Digital
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD51/067ARMZ-2RL
Manufacturer:
FUJISU
Quantity:
5 000
internal oscillator clock by 1, 2, 4, 8, 16, 32, 64, 128, 256,
512, or 1024 to give conversion times from 15.5 ms (Code
0x0A) to 16 seconds (Code 0x00). For example, a
conversion rate of 8 conversions per second means that
beginning at 125 ms intervals; the device performs a
conversion on the internal and external temperature
channels.
SMBus. The higher four bits of this register are unused and
must be set to 0. The default value of this register is 0x08,
giving a rate of 16 conversions per second. Use of slower
conversion times greatly reduces the device power
consumption, as shown in Table 4.
Limit Registers
THERM temperature limits for both local and remote
temperature measurements. The remote temperature high
and low limits span two registers each to contain an upper
and lower byte for each limit. There is also a THERM
hysteresis register. All limit registers can be written to and
read back over the SMBus. See Table 8 for address details
of the limit registers and their power-on default values.
limit registers perform a > comparison while the low limit
registers perform a ≤ comparison. For example, if the high
limit register is programmed with 80°C, then measuring
81°C results in an out-of-limit condition, setting a flag in the
status register. If the low limit register is programmed with
0°C, measuring 0°C or lower results in an out-of-limit
condition.
THERM low. When Pin 6 is configured as THERM2,
exceeding either the local or remote high limit asserts
Table 4. Conversion Rate Register Codes
0x0B to 0xFF
This register can be written to and read back over the
The ADT7461 has eight limit registers: high, low, and
When Pin 6 is configured as an ALERT output, the high
Exceeding either the local or remote THERM limit asserts
Code
0x0A
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
Conversion/Sec
Reserved
0.0625
0.125
0.25
0.5
16
32
64
1
2
4
8
Average Supply Current
mA Typ at VDD = 5.5 V
121.33
128.54
131.59
146.15
169.14
233.12
347.42
638.07
252.44
417.58
816.87
http://onsemi.com
10
THERM2 low. A default hysteresis value of 10°C is
provided that applies to both THERM channels. This
hysteresis value may be reprogrammed to any value after
powerup (Register Address 0x21).
data format is the same as the temperature measurement data
format. So, if the temperature measurement uses default
binary, the temperature limits also use the binary scale. If the
temperature measurement scale is switched, however, the
temperature limits do not switch automatically. The user
must reprogram the limit registers to the desired value in the
correct data format. For example, if the remote low limit is
set at 10°C and the default binary scale is being used, the
limit register value should be 0000 1010b. If the scale is
switched to offset binary, the value in the low temperature
limit register should be reprogrammed to be 0100 1010b.
Status Register
It contains status information for the ADT7461.
converting when it is high. The other bits in this register flag
the out-of-limit temperature measurements (Bits 6 to 3 and
Bits 1 to 0) and the remote sensor open circuit (Bit 2).
applies. If the local temperature measurement exceeds its
limits, Bit 6 (high limit) or Bit 5 (low limit) of the status
register asserts to flag this condition. If the remote
temperature measurement exceeds its limits, then Bit 4 (high
limit) or Bit 3 (low limit) asserts. Bit 2 asserts to flag an
open-circuit condition on the remote sensor. These five flags
are NOR’d together so if any of them is high, the ALERT
interrupt latch is set and the ALERT output goes low.
provided the error conditions causing the flags to be set have
gone away. A flag bit can be reset only if the corresponding
value register contains an in-limit measurement or if the
sensor is good.
status register. It resets when the ALERT output has been
serviced by the master reading the device address, provided
the error condition has gone away and the status register flag
bits are reset.
goes low to indicate the temperature measurements are
outside the programmed limits. The THERM output does
not need to be reset, unlike the ALERT output. Once the
measurements are within the limits, the corresponding status
register bits are reset automatically and the THERM output
goes high. The user may add hysteresis by programming
Register 0x21. The THERM output is reset only when the
temperature falls to limit value minus hysteresis value.
It is important to remember that the temperature limits
The status register is a read-only register at Address 0x02.
Bit 7 of the status register indicates the ADC is busy
If Pin 6 is configured as an ALERT output, the following
Reading the status register clears the five flags, Bits 6 to 2,
The ALERT interrupt latch is not reset by reading the
When Flag 1 and/or Flag 0 are set, the THERM output