CP2201-GM Silicon Laboratories Inc, CP2201-GM Datasheet - Page 55

• Manufacturer Part Number: CP2201-GM
• Description: IC ETH CTRLR SNGL-CHIP 28QFN
• Manufacturer: Silicon Laboratories Inc

Specifications of CP2201-GM

• Package / Case: 48-TQFP, 48-VQFP
• Controller Type: Ethernet Controller, MAC/10Base-T
• Interface: Parallel/Serial
• Voltage - Supply: 3.1 V ~ 3.6 V
• Current - Supply: 75mA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Ethernet Connection Type: 1000BASE-T or 100BASE-T or 10BASE-T
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Product: Ethernet Controllers
• Standard Supported: IEEE 802.3
• Data Rate: 10 Mbps or 100 Mbps or 1000 Mbps
• Maximum Operating Temperature: + 85 C
• No. Of Ports: 1
• Ethernet Type: IEEE 802.3
• Interface Type: Parallel
• Supply Current: 60mA
• Supply Voltage Range: 3.1V To 3.6V
• Operating Temperature Range: -40°C To +85°C
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 336-1326 - KIT REF DESIGN PWR OVER ETHERNET336-1316 - KIT EVAL FOR CP2201 ETH CTRLR
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 336-1313

Note: This register contains bits 40-32 of the Transmit Status Vector.
Bits 7-0: TXSTA4: Total Bytes Transmitted Low Byte
Note: This register contains bits 31–24 of the Transmit Status Vector.
Bit 7:
Bit 6:
Bit 5:
Bit 4:
Bit 3:
Bit 2:
Bit 1:
Bit 0:
TXURUN TXJUMBO TXLTCL
Bit7
Bit7
R
R
The least significant 8-bits of the total number of bytes transmitted on the wire, including all bytes
from collided attempts.
TXURUN: Transmit Under-Run
0: Transmit under-run did not occur.
1: Packet aborted due to data under-run condition.
TXJUMBO: Jumbo Packet Detected
0: Transmitted packet was not oversized.
1: Packet aborted due to its excessive size.
TXLTCL: Late Collision Detected
0: Late collision was not detected.
1: Packet aborted due to the detection of a collision after the 51.2 us collision window.
TXEXCL: Excessive Collisions Detected
0: Number of collisions on transmission was less than 16.
1: Packet aborted due to detection of 16 or more collisions.
TXEXDE: Excessive Delay Detected
0: Packet was transmitted without an excessive delay (greater than 2.42 ms). Please check other
flags for information.
1: Packet was aborted due to an excessive delay (greater than 2.42 ms).
TXDE: Delay Detected
0: Packet was transmitted with no delay or was aborted. Please check other flags for information.
1: Packet was transmitted, but had some delay (less than 2.4 ms).
TXBCAST: Transmitted Broadcast Packet
0: Transmitted packet did not have a broadcast destination address.
1: Transmitted packet had a broadcast destination address.
TXMCAST: Transmitted Multicast Packet
0: Transmitted packet did not have a multicast destination address.
1: Transmit packet had a multicast destination address.
Bit6
Bit6
R
R
Register 29. TXSTA4: Transmit Status Vector 4
Register 30. TXSTA3: Transmit Status Vector 3
Bit5
Bit5
R
R
TXEXCL
Bit4
Bit4
R
R
TXEXDE
Bit3
Bit3
R
R
Rev. 1.0
TXDE
Bit2
Bit2
R
R
TXBCAST TXMCAST 00000000
Bit1
Bit1
R
R
Bit0
Bit0
R
R
CP2200/1
00000000
Reset Value
Reset Value
Address:
Address:
0x5E
0x5F
55