ISP1161A1BM ST-Ericsson Inc, ISP1161A1BM Datasheet - Page 133

no-image

ISP1161A1BM

Manufacturer Part Number
ISP1161A1BM
Description
IC USB HOST/DEVICE CTRLR 64-LQFP
Manufacturer
ST-Ericsson Inc
Datasheet

Specifications of ISP1161A1BM

Controller Type
USB 2.0 Controller
Interface
Parallel
Voltage - Supply
3.3V, 5V
Current - Supply
47mA
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
64-LQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
568-1163
ISP1161A1BM,557

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISP1161A1BM
Manufacturer:
NXP
Quantity:
513
Part Number:
ISP1161A1BM
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Part Number:
ISP1161A1BMGA
Manufacturer:
EPCOS
Quantity:
6 700
Part Number:
ISP1161A1BMGA
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Company:
Part Number:
ISP1161A1BMGA
Quantity:
3 000
Part Number:
ISP1161A1BMUM
Manufacturer:
LUMEX
Quantity:
12 000
Part Number:
ISP1161A1BMUM
Manufacturer:
ST-Ericsson Inc
Quantity:
10 000
Philips Semiconductors
24. Soldering
9397 750 13961
Product data
24.1 Introduction to soldering surface mount packages
24.2 Reflow soldering
24.3 Wave soldering
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended. In these situations
reflow soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270 C depending on solder
paste material. The top-surface temperature of the packages should preferably be
kept:
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
below 225 C (SnPb process) or below 245 C (Pb-free process)
below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
thick/large packages.
Rev. 03 — 23 December 2004
2.5 mm
USB single-chip host and device controller
3
so called small/thin packages.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
350 mm
ISP1161A1
3
so called
132 of 136

Related parts for ISP1161A1BM