PIC18F8520-I/PT Microchip Technology Inc., PIC18F8520-I/PT Datasheet - Page 172

no-image

PIC18F8520-I/PT

Manufacturer Part Number
PIC18F8520-I/PT
Description
80 PIN, 32 KB FLASH, 2048 RAM, 68 I/O
Manufacturer
Microchip Technology Inc.
Datasheet

Specifications of PIC18F8520-I/PT

A/d Inputs
16-Channel, 10-Bit
Comparators
2
Cpu Speed
10 MIPS
Eeprom Memory
1024 Bytes
Input Output
68
Interface
I2C/SPI/UART/USART
Memory Type
Flash
Number Of Bits
8
Package Type
80-pin TQFP
Programmable Memory
32K Bytes
Ram Size
2K Bytes
Speed
40 MHz
Timers
2-8-bit, 3-16-bit
Voltage, Range
2-5.5 V
Lead Free Status / Rohs Status
RoHS Compliant part

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
PIC18F8520-I/PT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
PIC18F8520-I/PT
Manufacturer:
MICROCHIP-Pb
Quantity:
6 416
Part Number:
PIC18F8520-I/PT
Manufacturer:
MICROCHIP-Pb
Quantity:
3 827
Part Number:
PIC18F8520-I/PT
Manufacturer:
MICROCHIP-Pb
Quantity:
5 738
Part Number:
PIC18F8520-I/PT
Manufacturer:
MICRCOHI
Quantity:
20 000
PIC18F6520/8520/6620/8620/6720/8720
17.4.2
The MSSP module functions are enabled by setting
MSSP Enable bit, SSPEN (SSPCON<5>).
The SSPCON1 register allows control of the I
ation. Four mode selection bits (SSPCON<3:0>) allow
one of the following I
• I
• I
• I
• I
• I
• I
Selection of any I
forces the SCL and SDA pins to be open-drain, pro-
vided these pins are programmed to inputs by setting
the appropriate TRISC bits. To ensure proper operation
of the module, pull-up resistors must be provided
externally to the SCL and SDA pins.
17.4.3
In Slave mode, the SCL and SDA pins must be config-
ured as inputs (TRISC<4:3> set). The MSSP module
will override the input state with the output data when
required (slave-transmitter).
The I
interrupt on an address match. Through the mode
select bits, the user can also choose to interrupt on
Start and Stop bits
When an address is matched or the data transfer after
an address match is received, the hardware automati-
cally will generate the Acknowledge (ACK) pulse and
load the SSPBUF register with the received value
currently in the SSPSR register.
Any combination of the following conditions will cause
the MSSP module not to give this ACK pulse:
• The Buffer Full bit BF (SSPSTAT<0>) was set
• The overflow bit SSPOV (SSPCON<6>) was set
In this case, the SSPSR register value is not loaded
into the SSPBUF, but bit SSPIF (PIR1<3>) is set. The
BF bit is cleared by reading the SSPBUF register, while
bit SSPOV is cleared through software.
The SCL clock input must have a minimum high and
low for proper operation. The high and low times of the
I
MSSP module, are shown in timing parameter #100
and parameter #101.
DS39609B-page 170
2
C specification, as well as the requirement of the
Stop bit interrupts enabled
Stop bit interrupts enabled
Idle
before the transfer was received.
before the transfer was received.
2
2
2
2
2
2
C Master mode, clock = (F
C Slave mode (7-bit address)
C Slave mode (10-bit address)
C Slave mode (7-bit address), with Start and
C Slave mode (10-bit address), with Start and
C Firmware Controlled Master mode, slave is
2
C Slave mode hardware will always generate an
OPERATION
SLAVE MODE
2
C mode, with the SSPEN bit set,
2
C modes to be selected:
OSC
/4) x (SSPADD + 1)
2
C oper-
17.4.3.1
Once the MSSP module has been enabled, it waits for
a Start condition to occur. Following the Start condition,
the 8 bits are shifted into the SSPSR register. All incom-
ing bits are sampled with the rising edge of the clock
(SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match and the BF
and SSPOV bits are clear, the following events occur:
1.
2.
3.
4.
In 10-bit Address mode, two address bytes need to be
received by the slave. The five Most Significant bits
(MSbs) of the first address byte specify if this is a 10-bit
address. Bit R/W (SSPSTAT<2>) must specify a write
so the slave device will receive the second address
byte. For a 10-bit address, the first byte would equal
‘11110 A9 A8 0’, where ‘A9’ and ‘A8’ are the two
MSbs of the address. The sequence of events for
10-bit address is as follows, with steps 7 through 9 for
the slave-transmitter:
1.
2.
3.
4.
5.
6.
7.
8.
9.
The SSPSR register value is loaded into the
SSPBUF register.
The Buffer Full bit BF is set.
An ACK pulse is generated.
MSSP Interrupt Flag bit, SSPIF (PIR1<3>), is
set (interrupt is generated, if enabled) on the
falling edge of the ninth SCL pulse.
Receive first (high) byte of address (bits SSPIF,
BF and bit UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive second (low) byte of address (bits
SSPIF, BF and UA are set).
Update the SSPADD register with the first (high)
byte of address. If match releases SCL line, this
will clear bit UA.
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive Repeated Start condition.
Receive first (high) byte of address (bits SSPIF
and BF are set).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Addressing
 2004 Microchip Technology Inc.

Related parts for PIC18F8520-I/PT