LTC485CS8#TRPBF Linear Technology, LTC485CS8#TRPBF Datasheet
![IC TXRX INTRFC RS485 LOPWR 8SOIC](/photos/6/62/66297/8-soic_05-08-1610_sml.jpg)
LTC485CS8#TRPBF
Specifications of LTC485CS8#TRPBF
Available stocks
Related parts for LTC485CS8#TRPBF
LTC485CS8#TRPBF Summary of contents
Page 1
... The receiver has a fail-safe feature which guarantees a high output state when the inputs are left open. The LTC485 is fully specified over the commercial and extended industrial temperature range. , LTC and LT are registered trademarks of Linear Technology Corporation LTC485 • TA01 ...
Page 2
LTC485 BSOLUTE (Note 1) Supply Voltage ....................................................... 12V Control Input Voltages ................... – 0. Driver Input Voltage ....................... – 0. Driver Output Voltage ........................................... ±14V Receiver Input Voltage .......................................... ...
Page 3
U SWITCHI G CHARACTERISTICS temperature range, otherwise specifications are at T SYMBOL PARAMETER I Supply Current CC I Driver Short-Circuit Current, V OSD1 OUT I Driver Short-Circuit Current, V OSD2 OUT I Receiver Short-Circuit Current OSR t Driver Input to ...
Page 4
LTC485 W U TYPICAL PERFOR A Receiver Output Low Voltage vs Temperature 0 8mA 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 –50 – 125 75 100 TEMPERATURE (°C) LTC485 • TPC03 Driver Output ...
Page 5
CTIO S RO (Pin 1): Receiver Output. If the receiver output is enabled(RE low), then if A > 200mV, RO will be high < 200mV, then RO will be ...
Page 6
LTC485 U W SWITCHI WAVEFOR OD2 A, B –V OD2 ...
Page 7
U U APPLICATIO S I FOR ATIO Basic Theory of Operation Previous RS485 transceivers have been designed using bipolar technology because the common-mode range of the device must extend beyond the supplies and the device must be immune to ESD ...
Page 8
LTC485 U U APPLICATIO S I FOR ATIO The LTC485 output stage will maintain a high impedance state until the breakdown of the N-channel or P-channel is reached when going positive or negative respectively. The output will be clamped to ...
Page 9
U U APPLICATIO S I FOR ATIO LTC485 Line Length vs Data Rate The maximum line length allowable for the RS422/RS485 standard is 4000 feet. A LTC485 B 4000 FT 26AWG NOISE TWISTED PAIR TTL GENERATOR IN Figure 14. Line ...
Page 10
LTC485 TYPICAL APPLICATIO S PACKAGE DESCRIPTIO CORNER LEADS OPTION 0.045 – 0.068 (1.143 – 1.727) FULL LEAD OPTION 0.300 BSC (0.762 BSC) 0.008 – 0.018 (0.203 – 0.457) NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS 10 ...
Page 11
... FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 12
... Industry-Standard Pinout, 500ps Propagation Delay Skew LTC490/LTC491 Pin Compatible Highest Speed, LTC486/LTC487 Pin Compatible ±15kV ESD, LTC490 Pin Compatible ±15kV ESD, Fail-Safe (LT1785A) ±15kV ESD, Fail-Safe (LT1791A) www.linear.com ● sn485 LTC485ffs LT/LCG 1101 1.5K REV F • PRINTED IN THE USA © LINEAR TECHNOLOGY CORPORATION 1994 ...