PIC16F88-I/SO Microchip Technology Inc., PIC16F88-I/SO Datasheet - Page 43

• Manufacturer Part Number: PIC16F88-I/SO
• Description: 18 PIN, 7 KB FLASH, 368 RAM, 16 I/O
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F88-I/SO

• A/d Inputs: 7-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Input Output: 16
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 18-pin SOIC
• Programmable Memory: 7K Bytes
• Ram Size: 368 Bytes
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

FIGURE 4-6:
4.6.4
The IRCF bits can be modified at any time regardless of
which clock source is currently being used as the
system clock. The internal oscillator allows users to
change the frequency during run time. This is achieved
by modifying the IRCF bits in the OSCCON register.
The sequence of events that occur after the IRCF bits
are modified is dependent upon the initial value of the
IRCF bits before they are modified. If the INTRC
(31.25 kHz, IRCF<2:0> = 000) is running and the IRCF
bits are modified to any other value than ‘000’, a 4 ms
(approx.) clock switch delay is turned on. Code execu-
tion continues at a higher than expected frequency
while the new frequency stabilizes. Time sensitive code
should wait for the IOFS bit in the OSCCON register to
become set before continuing. This bit can be moni-
tored to ensure that the frequency is stable before using
the system clock in time critical applications.
If the IRCF bits are modified while the internal oscillator
is running at any other frequency than INTRC
(31.25 kHz, IRCF<2:0>
4 ms (approx.) clock switch delay. The new INTOSC
frequency will be stable immediately after the eight fall-
ing edges. The IOFS bit will remain set after clock
switching occurs.
 2005 Microchip Technology Inc.
Note:
T1OSO
T1OSI
OSC2
OSC1
MODIFYING THE IRCF BITS
Caution must be taken when modifying the
IRCF bits using BCF or BSF instructions. It
is possible to modify the IRCF bits to a
frequency that may be out of the V
ification range; for example, V
and IRCF = 111 (8 MHz).
Primary Oscillator
Secondary Oscillator
PIC16F87/88 CLOCK DIAGRAM
31.25 kHz
(INTRC)
000), there is no need for a
Oscillator
31.25 kHz
Internal
Source
Sleep
T1OSCEN
Enable
Oscillator
Block
(INTOSC)
8 MHz
DD
DD
= 2.0V
spec-
31.25 kHz
500 kHz
250 kHz
125 kHz
8 MHz
4 MHz
2 MHz
1 MHz
OSCCON<6:4>
4.6.5
Following are three different sequences for switching
the internal RC oscillator frequency.
• Clock before switch: 31.25 kHz (IRCF<2:0> = 000)
1.
2.
3.
4.
5.
• Clock before switch: One of INTOSC/INTOSC
1.
2.
3.
4.
111
110
101
100
011
010
001
000
postscaler (IRCF<2:0>
IRCF bits are modified to an INTOSC/INTOSC
postscaler frequency.
The clock switching circuitry waits for a falling
edge of the current clock, at which point CLKO
is held low.
The clock switching circuitry then waits for eight
falling edges of requested clock, after which it
switches CLKO to this new clock source.
The IOFS bit is clear to indicate that the clock is
unstable and a 4 ms (approx.) delay is started.
Time dependent code should wait for IOFS to
become set.
Switchover is complete.
IRCF
(IRCF<2:0> = 000).
The clock switching circuitry waits for a falling
edge of the current clock, at which point CLKO
is held low.
The clock switching circuitry then waits for eight
falling edges of requested clock, after which it
switches CLKO to this new clock source.
Oscillator switchover is complete.
To Timer1
LP, XT, HS, RC, EC
CLOCK TRANSITION SEQUENCE
bits
Internal Oscillator
Configuration Word 1 (FOSC2:FOSC0)
are
T1OSC
PIC16F87/88
SCS<1:0> (T1OSC)
modified
000)
DS30487C-page 41
WDT, FSCM
to
Peripherals
INTRC
CPU