PIC16F887-I/PT Microchip Technology Inc., PIC16F887-I/PT Datasheet - Page 178

• Manufacturer Part Number: PIC16F887-I/PT
• Description: MCU, 8-Bit, 8KW Flash, 368 RAM, 36 I/O, TQFP-44
• Manufacturer: Microchip Technology Inc.

Specifications of PIC16F887-I/PT

• A/d Inputs: 14-Channel, 10-Bit
• Comparators: 2
• Cpu Speed: 5 MIPS
• Eeprom Memory: 256 Bytes
• Frequency: 20 MHz
• Input Output: 35
• Interface: I2C/SPI/USART
• Memory Type: Flash
• Number Of Bits: 8
• Package Type: 44-pin TFQP
• Programmable Memory: 14K Bytes
• Ram Size: 368 Bytes
• Resistance, Drain To Source On: Bytes
• Serial Interface: MSSP or EUSART
• Speed: 20 MHz
• Timers: 2-8-bit, 1-16-bit
• Voltage, Range: 2-5.5 V
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

PIC16F882/883/884/886/887
REGISTER 13-1:
DS41291D-page 176
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
R/W-0
SMP
SMP: Sample bit
SPI Master mode:
1 = Input data sampled at end of data output time
0 = Input data sampled at middle of data output time
SPI Slave mode:
SMP must be cleared when SPI is used in Slave mode
In I
1 = Slew rate control disabled for standard speed mode (100 kHz and 1 MHz)
0 = Slew rate control enabled for high speed mode (400 kHz)
CKE: SPI Clock Edge Select bit
CKP = 0:
1 = Data transmitted on rising edge of SCK
0 = Data transmitted on falling edge of SCK
CKP = 1:
1 = Data transmitted on falling edge of SCK
0 = Data transmitted on rising edge of SCK
D/A: Data/Address bit (I
1 = Indicates that the last byte received or transmitted was data
0 = Indicates that the last byte received or transmitted was address
P: Stop bit
(I
1 = Indicates that a Stop bit has been detected last (this bit is ‘0’ on Reset)
0 = Stop bit was not detected last
S: Start bit
(I
1 = Indicates that a Start bit has been detected last (this bit is ‘0’ on Reset)
0 = Start bit was not detected last
R/W: Read/Write bit information (I
This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to
the next Start bit, Stop bit, or not ACK bit.
In I
1 = Read
0 = Write
In I
1 = Transmit is in progress
0 = Transmit is not in progress
UA: Update Address bit (10-bit I
1 = Indicates that the user needs to update the address in the SSPADD register
0 = Address does not need to be updated
BF: Buffer Full Status bit
Receive (SPI and I
1 = Receive complete, SSPBUF is full
0 = Receive not complete, SSPBUF is empty
Transmit (I
1 = Data transmit in progress (does not include the ACK and Stop bits), SSPBUF is full
0 = Data transmit complete (does not include the ACK and Stop bits), SSPBUF is empty
2
2
C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.)
C mode only. This bit is cleared when the MSSP module is disabled, SSPEN is cleared.)
2
2
2
C Master or Slave mode:
C Slave mode:
C Master mode:
R/W-0
CKE
OR-ing this bit with SEN, RSEN, PEN, RCEN, or ACKEN will indicate if the MSSP is in Idle mode.
SSPSTAT: SSP STATUS REGISTER
2
C mode only):
W = Writable bit
‘1’ = Bit is set
2
C modes):
R-0
D/A
2
C mode only)
2
C mode only)
2
C mode only)
R-0
Preliminary
P
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R-0
S
R/W
R-0
© 2007 Microchip Technology Inc.
x = Bit is unknown
R-0
UA
R-0
BF
bit 0