MT48LC16M16A2P-75 L Micron Technology Inc, MT48LC16M16A2P-75 L Datasheet - Page 7

• Manufacturer Part Number: MT48LC16M16A2P-75 L
• Manufacturer: Micron Technology Inc
• Type: SDRAMr

Specifications of MT48LC16M16A2P-75 L

• Organization: 16Mx16
• Density: 256Mb
• Address Bus: 15b
• Access Time (max): 6/5.4ns
• Maximum Clock Rate: 133MHz
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 135mA
• Pin Count: 54
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / Rohs Status: Compliant

General Description
Automotive Temperature
PDF: 09005aef8091e6d1
256Mb_sdr.pdf - Rev. N 1/10 EN
The 256Mb SDRAM is a high-speed CMOS, dynamic random-access memory contain-
ing 268,435,456 bits. It is internally configured as a quad-bank DRAM with a synchro-
nous interface (all signals are registered on the positive edge of the clock signal, CLK).
Each of the x4’s 67,108,864-bit banks is organized as 8192 rows by 2048 columns by 4
bits. Each of the x8’s 67,108,864-bit banks is organized as 8192 rows by 1024 columns by
8 bits. Each of the x16’s 67,108,864-bit banks is organized as 8192 rows by 512 columns
by 16 bits.
Read and write accesses to the SDRAM are burst-oriented; accesses start at a selected
location and continue for a programmed number of locations in a programmed se-
quence. Accesses begin with the registration of an ACTIVE command, which is then
followed by a READ or WRITE command. The address bits registered coincident with
the ACTIVE command are used to select the bank and row to be accessed (BA[1:0] select
the bank; A[12:0] select the row). The address bits registered coincident with the READ
or WRITE command are used to select the starting column location for the burst access.
The SDRAM provides for programmable read or write burst lengths (BL) of 1, 2, 4, or 8
locations, or the full page, with a burst terminate option. An auto precharge function
may be enabled to provide a self-timed row precharge that is initiated at the end of the
burst sequence.
The 256Mb SDRAM uses an internal pipelined architecture to achieve high-speed oper-
ation. This architecture is compatible with the 2n rule of prefetch architectures, but it
also allows the column address to be changed on every clock cycle to achieve a high-
speed, fully random access. Precharging one bank while accessing one of the other
three banks will hide the PRECHARGE cycles and provide seamless, high-speed, random-
access operation.
The 256Mb SDRAM is designed to operate in 3.3V memory systems. An auto refresh
mode is provided, along with a power-saving, power-down mode. All inputs and out-
puts are LVTTL-compatible.
SDRAMs offer substantial advances in DRAM operating performance, including the abil-
ity to synchronously burst data at a high data rate with automatic column-address
generation, the ability to interleave between internal banks to hide precharge time, and
the capability to randomly change column addresses on each clock cycle during a burst
access.
The automotive temperature (AT) option adheres to the following specifications:
• 16ms refresh rate
• Self refresh not supported
• Ambient and case temperature cannot be less than –40°C or greater than +105°C
7
Micron Technology, Inc. reserves the right to change products or specifications without notice.
256Mb: x4, x8, x16 SDRAM
General Description
© 1999 Micron Technology, Inc. All rights reserved.