MC33390D Freescale Semiconductor, MC33390D Datasheet - Page 11

no-image

MC33390D

Manufacturer Part Number
MC33390D
Description
IC TRANSCEIVER SER LINK 8-SOIC
Manufacturer
Freescale Semiconductor
Type
Transceiverr
Datasheet

Specifications of MC33390D

Number Of Drivers/receivers
1/1
Voltage - Supply
9 V ~ 16 V
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Protocol
-
Other names
Q1163428B

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MC33390DR2
Manufacturer:
MOT
Quantity:
11 532
Part Number:
MC33390DR2G
Manufacturer:
ON
Quantity:
678
Part Number:
MC33390DR2G
Manufacturer:
MOT
Quantity:
29
Part Number:
MC33390DR2G
Manufacturer:
ON/安森美
Quantity:
20 000
Class B Module Inputs
Transmitter Data from the MCU (Tx)
buffer with hysteresis for noise immunity purposes. This pin
is a 5.0 V CMOS logic level input from the MCU following a
true logic protocol. A logic [0] input drives the BUS output to
0 V (via the external pull-down resistor to ground on each
node), while a logic [1] input produces a high voltage at the
BUS output. A logic [0] input level is guaranteed when the Tx
input pin is open-circuited by virtue of an internal 40 kΩ pull-
down resistor. No external resistor is required for its
operation.
Waveshaping and 4X / Loop
waveshaping, 5.0 V = waveshaping is disabled for 4X
transmitting, and high impedance = loopback mode of
operation. This is a logic level input used to select whether
waveshaping for the Class B output is enabled or disabled. A
logic [0] enables waveshaping, while a logic [1] disables
waveshaping. In the 4X mode, the BUS output rise time is
less than 2.0
the external RC pull-down to ground). In the loopback
condition, the Tx signal is fed back to the Rx output after
waveshaping without being transmitted onto the BUS. This
mode of operation is useful for system diagnostic purposes.
Class B Module Outputs
Transceiver Output (BUS)
bus. Its output follows the waveshaped waveform input. Its
output voltage is limited to 6.25 V to 8.0 V under normal
battery level conditions. The limited level is controlled by an
internal regulator/clamp circuit. Once the battery voltage
drops below 9.0 V, the regulator / clamp circuit saturates,
causing the bus voltage to track the battery voltage. A 1.5 kΩ
± 5% external resistor (as well as any 10.6 kΩ pull-down
resistors of any secondary nodes) sinks the current to
discharge the capacitors during high-to-low transitions. This
sourcing output is short circuit-protected (60 mA to 170 mA)
against a short to -2.0 V and sinks less than 1.0 mA when
shorted to V
shutdown circuit protects the source driver of the device. In
the event battery power is lost to the assembly, the bus
transmitter's output stage will be disabled and the leakage
current from the BUS output will not source or sink more than
100 µA of current. The transceiver will operate with a remote
ground offset of ± 2.0 V, but the lower corners of transmission
will not be rounded during this condition.
Analog Integrated Circuit Device Data
Freescale Semiconductor
The Tx input is a push-pull (N-channel / P-channel FETs)
This input is a tristateable input: 0 V = normal
This is the output driver stage that sources current to the
BAT
µs
and the fall time is less than 5.0
. If a short occurs, the overtemperature
TYPICAL APPLICATIONS
µs
(owing to
Receiver Output to the Microcontroller (Rx)
send received data to the microcontroller. It does not require
an external pull-up resistor to be used. The receiver is always
enabled and draws less than 65 µA of current from V
receive threshold is dependent on the state of the
The receiver circuitry is able to operate with V
low as 4.25 V and still remains capable of “waking up” the
33390 when remote Class B activity is detected.
on the bus, the receiver passes the bus message through to
the microcontroller. The 33390 does not automatically “wake
up” from a sleep state when bus activity occurs: the
microcontroller must tell it to do so.
voltage for Rx is specified as 4.75 V over an operating range
of -40°C to 125°C temperature and 7.0 V to 16 V V
maximum Rx voltage is compatible with the minimum V
voltage of microcontrollers to prevent the 33390 from
sourcing current to the microcontroller's output.
Switched Ground Output (LOAD)
pulls down the external resistor between the BUS and LOAD
outputs. In the event ground is lost to the assembly, the
LOAD output will bias itself “off” and will not leak more than
100 µA of current out of this pin.
Overtemperature Shutdown
duration, an overtemperature shutdown circuit “latches off”
the output source transistor whenever the die temperature
exceeds 150°C to 190°C. The output transistor remains
latched off until the Tx input is toggled from a logic [0] to a
logic [1]. The rising edge provides the clearing function,
provided the locally sensed temperature is 10°C to 15°C
below the latch-off temperature trip temperature.
Waveshaping
radiated EMI emissions.
Receiver Protocol
width (VPW) protocol. The microcontroller provides the VPW
decoding function. Once the receiver detects a transition on
Rx, it starts an internal counter. The initial “start of frame” bit
is a logic [1] and lasts 200 µs. For subsequent bits, if there is
a bus transition before 96 µs, one logic state is inferred. If
there is a bus transition after 96 µs, the other logic state is
inferred. The “end of data” bit is a logic [0] and lasts 200 µs.
If there is no activity on the bus for 280 µs to 320 µs following
a broadcast message, multiple unit nodes may arbitrate for
control of the next message. During an arbitration, after the
This is a 5.0 V CMOS compatible push-pull output used to
When the
In the Static Electrical Characteristics table, the maximum
Normally this output is a saturated switch to ground, which
If the BUS output becomes shorted to ground for any
Waveshaping is incorporated into the 33390 to minimize
The Class B communication scheme uses a variable pulse
SLEEP
pin is 0 V and message activity occurs
TYPICAL APPLICATIONS
BAT
voltages as
SLEEP
BAT
BAT
. This
. The
DD
33390
pin.
11

Related parts for MC33390D