ATA8202-PXQW 19 Atmel, ATA8202-PXQW 19 Datasheet - Page 14

• Manufacturer Part Number: ATA8202-PXQW 19
• Description: IC RX UHF ASK/FSK 433MHZ 24-VQFN
• Manufacturer: Atmel
• Series: -r

Specifications of ATA8202-PXQW 19

• Frequency: 433MHz
• Sensitivity: -113dBm
• Data Rate - Maximum: 9.6 kbps
• Modulation Or Protocol: ASK, FSK
• Applications: AMR, ISM, Security and Access
• Current - Receiving: 6.7mA
• Data Interface: *
• Memory Size: *
• Antenna Connector: *
• Features: -
• Voltage - Supply: 2.7 V ~ 3.3 V, 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-VQFN Exposed Pad
• Pin Count: 24
• Screening Level: Industrial
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: ATA8202-PXQW

2.6
2.7
14
In-band Disturbers, Data Filter, Quasi-peak Detector, Data Slicer
RSSI Output
ATA8201/ATA8202
If a disturbing signal falls into the received band, or if a blocker is not a continuous wave, the
performance of a receiver strongly depends on the circuits after the IF filter. Hence, the demod-
ulator, data filter, and data slicer are important.
The data filter of the ATA8201/ATA8202 functions also as a quasi-peak detector. This results in a
good suppression of above mentioned disturbers and exhibits a good carrier-to-noise perfor-
mance. The required useful-signal-to-disturbing-signal ratio, at a BER of 10
in ASK mode and less than 3 dB (BR_Range_0 to BR_Range_2) and 6 dB (BR_Range_3) in
FSK mode. Due to the many different possible waveforms, these numbers are measured for the
signal, as well as for disturbers, with peak amplitude values. Note that these values are
worst-case values and are valid for any type of modulation and modulating frequency of the dis-
turbing signal, as well as for the receiving signal. For many combinations, lower
carrier-to-disturbing-signal ratios are needed.
The output voltage of the pin RSSI is an analog voltage, proportional to the input power level.
Using the RSSI output signal, the signal strength of different transmitters can be distinguished.
The usable dynamic range of the RSSI amplifier is 65 dB, the input power range P(RF
–110 dBm to –45 dBm, and the gain is 15 mV/dB.
typical device at 315 MHz with VS3V_AVCC = VS5V = 3V and T
input as shown in
needed for the same RSSI results.
Figure 2-9.
As can be seen in
and supply voltage range of ±3 dB. The total variance over production, temperature, and supply
voltage range is ±9 dB.
Typical RSSI Characteristic at 315 MHz Versus Temperature and Supply Voltage
Table 2-2
Figure 2-9 on page
0.4
1.6
1.4
1.3
1.2
0.7
0.5
1.7
1.5
1.0
0.9
0.8
0.6
1.1
-13 0 -12 0 -110 -10 0 -9 0
and
Figure 2-1 on page
max: +9 dBm
14, for single devices there is a variance over temperature
-8 0
Pin (dBm)
-70
min: -9 dBm
Figure 2-9
7. At 433.92 MHz, 1 dB more signal level is
-6 0
-50
-4 0
shows the RSSI characteristic of a
-3 0
3V, 25˚C
amb
-2 0
= 25°C with a matched
-10
–3,
is less than 14 dB
4971C–INDCO–04/09
IN
) is