ISL54208IRZ Intersil, ISL54208IRZ Datasheet
ISL54208IRZ
Specifications of ISL54208IRZ
Available stocks
Related parts for ISL54208IRZ
ISL54208IRZ Summary of contents
Page 1
... All other trademarks mentioned are the property of their respective owners. ISL54208 FN6410 1.8V to 5.5V DD μ TQFN and TDFN Packages μ CONTROLLER USB D- HIGH-SPEED D+ TRANSCEIVER NTSC or PAL VIDEO AUDIO Intersil (and design registered trademark of Intersil Americas Inc. Copyright Intersil Americas Inc. 2006. All Rights Reserved ...
Page 2
... FR ISL54208IRZ-T 4208 ISL54208IRZ 4208 NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate or NiPdAu termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020 ...
Page 3
... Maximum Junction Temperature (Plastic Package +150° 0.3V) Maximum Storage Temperature Range -65°C to +150° 0.3V) DD Operating Conditions Temperature Range ISL54208IRUZ and ISL54208IRZ -40°C to +85°C or GND by specified amount are clamped. Limit current to maximum current ratings. DD Test Conditions 0.5V, (Notes 4, 6), unless otherwise specified. CTRLL TEST CONDITIONS = 3 ...
Page 4
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER OFF Leakage Current NOx(OFF NOx ON Leakage Current NOx DD V COMx DYNAMIC CHARACTERISTICS Turn-ON Time Turn-OFF Time OFF DD ...
Page 5
Electrical Specifications - 2.7V to 3.6V Supply PARAMETER Input Current CTRLH DD CTRL Pull-Down Resistor CTRL DD NOTES Input voltage to perform proper function. LOGIC 5. The algebraic convention, whereby the most negative ...
Page 6
Test Circuits and Waveforms /100mA ON 1 CTRL NCx V NCx V 1 100mA COMx GND Repeat test for all switches. FIGURE 3. AUDIO/VIDEO R ON CTRL NCx or NOx IMPEDANCE ANALYZER COMx Repeat test for all ...
Page 7
Test Circuits and Waveforms t ri 90% 50% 10% DIN+ t skew_i DIN- 90% 50% 10 90% 10% 50% OUT+ t skew_o OUT- 50% 90% 10 FIGURE 7A. MEASUREMENT POINTS 7 ISL54208 (Continued) V ...
Page 8
Application Block Diagrams VBUS VBUS 22kΩ 4MΩ LOGIC CONTROL VIA VBUS VOLTAGE FROM COMPUTER OR USB HUB Detailed Description The ISL54208 device is a dual single pole/double throw (SPDT) analog switch device that can operate from a single dc power ...
Page 9
NC1 and NC2 Audio/Video Switches The two NC (normally closed) audio/video switches (NC1, NC2) are 3Ω switches that can pass signals that swing below ground by as much as 1.5V. They ...
Page 10
ISL54208 Operation The discussion that follows will discuss using the ISL54208 in the typical application shown in the block diagrams on page 8. VDD SUPPLY The dc power supply connected at VDD (pin 1) provides the required bias voltage for ...
Page 11
EXTERNAL SERIES RESISTOR AT IN LOGIC CONTROL PIN The ISL54208 contains a clamp circuit between IN and VDD. Whenever the IN voltage is greater than the V more than 2.55V, current will flow through this clamp circuitry into the V ...
Page 12
Typical Performance Curves FIGURE 14. EYE PATTERN: 480Mbps WITH NOx SWITCHES IN THE SIGNAL PATH 1 NOx Switch 50Ω 0. P-P P-P 1M 10M FREQUENCY (Hz) FIGURE ...
Page 13
Typical Performance Curves 1 NCx Switches 75Ω 0. P-P P-P 1M 10M FREQUENCY (Hz) FIGURE 17. Die Characteristics SUBSTRATE POTENTIAL (POWERED UP): GND (TDFN Paddle Connection: Tie ...
Page 14
... Maximum allowable burrs is 0.076mm in all directions. 9. Same as JEDEC MO-255UABD except: TERMINAL TIP No lead-pull-back, "A" MIN dimension = 0.45 not 0.50mm "L" MAX dimension = 0.45 not 0.42mm. 10. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB389. L MILLIMETERS MIN NOMINAL MAX A 0 ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...