1-1734709-5 TE Connectivity, 1-1734709-5 Datasheet

1.0 WTB HDR SR RA 15 POS

1-1734709-5

Manufacturer Part Number
1-1734709-5
Description
1.0 WTB HDR SR RA 15 POS
Manufacturer
TE Connectivity
Datasheets

Specifications of 1-1734709-5

Product Type
Connector
Connector Type
Header
Mount Angle
Right Angle
Number Of Positions
15
Centerline (mm [in])
1.00 [0.039]
Number Of Rows
Single
Locking Interface
Without
Contact Type
Pin
Contact Termination Type
Surface Mount
Contact Base Material
Phosphor Bronze
Contact Finish
Matte Tin over Nickel
Connector Style
Plug
Housing Color
Natural
Ul Flammability Rating
UL 94V-0
Housing Material
Thermoplastic - GF
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Reflow solder capable to 245°C, Reflow solder capable to 260°C
Rohs/elv Compliance History
Always was RoHS compliant
Packaging Quantity
1,500/Reel
DR
Angus Wu
©2007 Tyco Electronics Corporation
Taipei, Taiwan
All International Rights Reserved.
1.
1.1.
1.2.
2.
2.1.
2.2.
3.
3.1.
3.2.
3.3.
3.4.
SCOPE
Contents
This specification covers the performance, tests and quality requirements for the Tyco Electronics
Wire-To-Board Serial, SMT, Pitch 1.0 connector.
Qualification
When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All
inspections shall be performed using the applicable inspection plan and product drawing.
APPLICABLE DOCUMENT
The following Tyco documents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the document applies. In the event of conflict between the
requirements of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirements of this specification and the referenced documents,
this specification shall take precedence.
Tyco Electronics Documents
Commercial Standard
REQUIREMENTS
Design and Construction
Product shall be of the design, construction and physical dimensions specified on the applicable product
drawing.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
Ratings
A.
B.
C.
Performance Requirement and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per EIA-364.
109-201: Component Heat Resistance to Lead-Free Reflow Soldering.
501-57283: Qualification Test Report.
Voltage: 50 volts AC/DC rms.
Current: 1 ampere for AWG #28.
Temperature: -55 to 105°C.
JESD22-B102D: Solderability Test Method.
* Trademark
│ Indicates change
Product
Specification
Wire-To-Board Serial, SMT, Pitch 1.0 connector
For latest revision, visit our website at www.tycoelectronics.com\documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
03JUL06 Wei-Jer Ke
DATE APVD
108-57264
03-NOV-2009 Rev D
LOC DW
03JUL06
1 of 4
DATE

Related parts for 1-1734709-5

1-1734709-5 Summary of contents

Page 1

... This specification covers the performance, tests and quality requirements for the Tyco Electronics Wire-To-Board Serial, SMT, Pitch 1.0 connector. 1.2. Qualification When tests are performed on the subject product line, procedures specified in Figure 1 shall be used. All inspections shall be performed using the applicable inspection plan and product drawing. 2. APPLICABLE DOCUMENT The following Tyco documents form a part of this specification to the extent specified herein ...

Page 2

... Measure the force required to mate connector Operation Speed: 10 mm/min. Measure the force required to unmate connector Operation Speed: 10 cycle/min. No. of Cycles: 50 Cycles Subject mated connectors to 10-55-10 Hz traversed in 1minutes at 1.52mm amplitude 2 Hours each of 3 mutually perpendicular planes, passing DC 100mA current during the test. 2 Accelerate Velocity: 490m/s ...

Page 3

... After test, rinse the sample with water and recondition the room temperature for 1 hour. Pre Heat: 100 – 150° sec Min. Heat: 210°C, 30 sec. Min. Peak Temp.: 235°C Pre-soak condition, 40°C / 95﹪R.H. for 48 hours. Pre Heat: 150 ~ 180° ...

Page 4

... Thermal Shock Humidity Temperature Cycling Salt Spray Solderability Resistance to Reflow Soldering Heat Insertion & withdraw force Cramp Retention force Current Rating NOTE (a) Numbers indicate sequence in which test are performed. Rev Test Sequence ( Figure 2 Termination Resistance Measurement Point Figure 3 108-57264 Test Group F ...

Related keywords