903063 PRO SIGNAL, 903063 Datasheet
903063
Manufacturer Part Number
903063
Description
55T8243
Manufacturer
PRO SIGNAL
Datasheet
1.903063.pdf
(1 pages)
Specifications of 903063
Rohs Compliant
YES
L25.5/R1
Warnings
Required Tools
Hardware
Installation (continued)
Part 2 – Attach the Mount To Your Display
1. Determine the proper length of bolt for attaching the mount to your display by
2. Attach the mount to your display using the hardware determined in Step 1 (see
1. Make sure these instructions are read and completely understood before attempting
2. The wall or mounting surface must be capable of supporting the combined weight of
3. Safety gear and proper tools must be used. Failure to do so can result in damage or
4. Follow all instructions and recommendations regarding adequate ventilation and
examining the back of the display:
illustration). To avoid damage to your display, do not over-tighten these bolts.
You will need the following tools to complete your installation:
• Phillips Head Screw Driver
• Electric or Portable Drill
• Stud Finder and 1/8” (3 mm) Drill Bit for Drywall Installation
• 5/16” (8 mm) Masonry Bit for Concrete Installation
Check to make sure all hardware has been included with your mount. You should nd
the following:
installation. If you are unsure of any part of this installation, contact a professional
installer for assistance.
the mount and the display; otherwise the structure must be reinforced.
injury.
suitable locations for mounting your display. Consult the owner‘s manual for your
display for more information.
a) If your display has a at back, you will use one of the shorter bolts from the
b) If the back of your display is curved or recessed, or if there are any obstructions
(B) Concrete Anchor x2
hardware kit (C or E). Carefully test each of the shorter bolts with your display to
determine the correct diameter to use.
preventing the mount from resting at against the back, you will use one of the
longer bolts (D or F) along with a spacer (G or H). Carefully test each of the longer
bolts with your display to determine the correct diameter to use. Use the Small
Spacer (G) with the M4 x 30 Bolts (D) and the Large Spacer (H) with the M6 x 35
Bolts (F).
(A) Drywall Screw x2
(I) 3 mm Allen Key x1
(C) M4 x 12 Bolt x4
(D) M6 x 12 Bolt x4
Only if using E or F
Spacer (G or H)
Bolt (C, D, E, or F)
(E) M4 x 30 Bolt x4
(F) M6 x 35 Bolt x4
LCD Wall Mount Installation Guide
(J) 4 mm Allen Key x1
(G) Small Spacer x4
(H) Large Spacer x4
Part 1a – Install the Wall Piece (Drywall)
1. Using a high quality stud nder, locate and mark one stud for installing the wall mount.
2. Place the wall piece portion of the mount over the center of the marked stud and level
3. Mark o the two holes for securing the mount and place the wall piece aside.
4. Using an electric or portable drill with 1/8” (3 mm) bit, drill the marked holes.
5. Move the wall piece portion of the mount back into place and attach it using the
Part 1b – Install the Wall Piece (Concrete)
1. Place the wall piece portion of the mount in the desired location and level it using the
2. Mark o the two holes for securing the mount and place the wall piece aside.
3. Using an electric or portable drill with 5/16” (8 mm) masonry bit, drill the marked holes.
4. Insert a Concrete Anchor (B) into each hole. The anchors must be inserted until they are
5. Move the wall piece portion of the mount back into place and attach it using the
Part 3 – Slide the Pieces Together
1. To complete the installation, simply slide the mount with your LCD attached into the
2. To remove the mount, push in on the plastic tab and then slide the mount up.
3. For additional security and stability, tighten the set screw located on the base of the arm
4. Use the cable management hook (see illustration) to keep the power cord and other
5. To change the tilt angle, hold the display with one hand and loosen the tilt adjustment
6. If you nd that a joint is too di cult to move or has become too loose, you can adjust
Installation
Installation (continued)
Use a small nail or awl to verify the location of the stud.
it using the integrated bubble guide.
Drywall Screws (A) from the hardware kit. Make sure both screws are snug, but do not
to over-tighten them.
integrated bubble guide.
After drilling, remove any excess dust from the holes.
place if necessary.
Drywall Screws (A) from the hardware kit. Make sure both screws are snug, but do not
to over-tighten them.
wall piece. The plastic tab at the top of wall piece should click indicating that the mount
is secure.
piece using the 3 mm Allen Key (I) supplied in the hardware kit.
cables for your display in order while adjusting the mount.
knob. Move the display to the desired position and re-tighten the knob. Other
adjustments can be made by simple moving the mount into the desired position.
the tightness of that joint using the 4 mm Allen Key (J) supplied in the hardware kit.
ush with the concrete surface; a hammer can be used to lightly tap each anchor into
Drywall Screw (A)
Plastic Tab
Cable Management Hook
Tilt Adjustment Knob
Set Screw
Wall Piece
Related parts for 903063
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
PIEZO SIREN, 12VDC
Manufacturer:
PRO SIGNAL
Datasheet:
Part Number:
Description:
PIEZO SIREN, 12VDC
Manufacturer:
PRO SIGNAL
Datasheet:
Part Number:
Description:
PATCH LEAD, CAT 5E, 7M GREY
Manufacturer:
PRO SIGNAL
Datasheet: