ATMEGA328P-20PU Atmel, ATMEGA328P-20PU Datasheet - Page 55

• Manufacturer Part Number: ATMEGA328P-20PU
• Manufacturer: Atmel

Specifications of ATMEGA328P-20PU

• Cpu Family: ATmega
• Device Core: AVR
• Device Core Size: 8b
• Frequency (max): 20MHz
• Interface Type: SPI/TWI/USART
• Program Memory Type: Flash
• Program Memory Size: 32KB
• Total Internal Ram Size: 2KB
• # I/os (max): 23
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• On-chip Adc: 6-chx10-bit
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 28
• Package Type: PDIP
• Lead Free Status / Rohs Status: Compliant

8025K–AVR–10/09
WDIF automatically by hardware (the Watchdog goes to System Reset Mode). This is useful for
keeping the Watchdog Timer security while using the interrupt. To stay in Interrupt and System
Reset Mode, WDIE must be set after each interrupt. This should however not be done within the
interrupt service routine itself, as this might compromise the safety-function of the Watchdog
System Reset mode. If the interrupt is not executed before the next time-out, a System Reset
will be applied.
Table 10-1.
Note:
• Bit 4 - WDCE: Watchdog Change Enable
This bit is used in timed sequences for changing WDE and prescaler bits. To clear the WDE bit,
and/or change the prescaler bits, WDCE must be set.
Once written to one, hardware will clear WDCE after four clock cycles.
• Bit 3 - WDE: Watchdog System Reset Enable
WDE is overridden by WDRF in MCUSR. This means that WDE is always set when WDRF is
set. To clear WDE, WDRF must be cleared first. This feature ensures multiple resets during con-
ditions causing failure, and a safe start-up after the failure.
• Bit 5, 2..0 - WDP3..0: Watchdog Timer Prescaler 3, 2, 1 and 0
The WDP3..0 bits determine the Watchdog Timer prescaling when the Watchdog Timer is run-
ning. The different prescaling values and their corresponding time-out periods are shown in
Table 10-2 on page
Table 10-2.
WDTON
WDP3
0
0
0
0
0
0
0
0
1
1
1
1
0
1. WDTON Fuse set to “0” means programmed and “1” means unprogrammed.
(1)
WDP2
0
0
0
0
1
1
1
1
Watchdog Timer Configuration
Watchdog Timer Prescale Select
WDE
0
0
1
1
x
55.
WDP1
0
0
1
1
0
0
1
1
WDIE
WDP0
0
1
0
1
x
0
1
0
1
0
1
0
1
Mode
Stopped
Interrupt Mode
System Reset Mode
Interrupt and System Reset
Mode
System Reset Mode
Number of WDT Oscillator
128K (131072) cycles
256K (262144) cycles
16K (16384) cycles
32K (32768) cycles
64K (65536) cycles
2K (2048) cycles
4K (4096) cycles
8K (8192) cycles
Cycles
ATmega48P/88P/168P
Action on Time-out
None
Interrupt
Reset
Interrupt, then go to System
Reset Mode
Reset
Typical Time-out at
V
CC
0.125 s
16 ms
32 ms
64 ms
0.25 s
0.5 s
1.0 s
2.0 s
= 5.0V
55