M27C1024-10C1 STMicroelectronics, M27C1024-10C1 Datasheet
M27C1024-10C1
Specifications of M27C1024-10C1
Available stocks
Related parts for M27C1024-10C1
M27C1024-10C1 Summary of contents
Page 1
... ELECTRONIC SIGNATURE – Manufacturer Code: 20h – Device Code: 8Ch DESCRIPTION The M27C1024 Mbit EPROM offered in the two ranges UV (ultra violet erase) and OTP (one time programmable ideally suited for micro- processor systems requiring large data or program storage and is organized as 65,536 words of 16 bits ...
Page 2
... A10 A11 A12 A13 A14 A15 M27C1024 31 (Normal DQ15 DQ14 DQ13 DQ12 DQ11 DQ10 DQ9 DQ8 20 21 AI01582 2/16 Figure 3. LCC Connections Q12 Q11 Q10 M27C1024 Table 1. Signal Names A0-A15 Q0-Q15 DQ0 DQ1 NC DQ2 DQ3 DQ4 DQ5 DQ6 DQ7 V SS ...
Page 3
... Note: Outputs Q15-Q8 are set to ’0’. (1) Parameter (3) +2V for a period less than 20ns Pulse M27C1024 Value Unit –40 to 125 C –50 to 125 C –65 to 150 C – – –2 to 13.5 V – Q15- Data Output Hi Data Input PP V Data Output Codes Hex Data 0 0 20h 0 0 ...
Page 4
... Standby Mode The M27C1024 has a standby mode which reduc- es the active current from 35mA to 100 A. The M27C1024 is placed in the standby mode by applying a TTL high signal to the E input. When in the standby mode, the outputs are in a high imped- ance state, independent of the G input. ...
Page 5
... M27C1024 10 Min Max Unit 100 A 100 A –0.3 0 0 – M27C1024 (3) (3) Unit -45 -55 Min Max Min Max 5/16 ...
Page 6
... F bulk electrolytic capacitor should be used between V CC es. The bulk capacitor should be located near the power supply connection point.The purpose of the bulk capacitor is to overcome the voltage drop caused by the inductive effects of PCB traces 10 M27C1024 -10/-12 -80/-90 Unit -15/-20 Min Max Min Max 70 80 100 ns ...
Page 7
... Sampled only, not 100% tested. Programming When delivered (and after each ’1’s erasure for UV EPROM), all bits of the M27C1024 are in the ’1’ state. Data is introduced by selectively program- ming ’0’s into the desired bit locations. Although only ’0’s will be programmed, both ’1’s and ’0’s can be present in the data word. The only way to change a ’ ...
Page 8
... Programming of multiple M27C1024s in parallel with different data is also easily accomplished. Ex- cept for E, all like inputs including G of the parallel M27C1024 may be common. A TTL low level pulse applied to a M27C1024’ input, with E low and V at 12.75V, will program that M27C1024 high level E input inhibits the other M27C1024s from being programmed ...
Page 9
... M27C1024 in about 3 years, while it would take approximately 1 week to cause erasure when exposed to direct sunlight. If the M27C1024 exposed to these types of lighting conditions for extended pe- riods of time suggested that opaque labels ...
Page 10
... C Optio Additional Burn- Tape & Reel Packing Note: 1. High Speed, see AC Characteristics section for further information. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this de- vice, please contact the STMicroelectronics Sales Office nearest to you. 10/16 M27C1024 - ...
Page 11
... Table 13. Revision History Date September 1998 First Issue 20-Sep-2000 AN620 Reference removed 29-Nov-200 PLCC codification changed (Table 12) 28-Nov-2001 tEHQZ, tGHQZ values changed (35ns speed class, Table 8) Revision Details M27C1024 11/16 ...
Page 12
... M27C1024 Table 14. FDIP40W - 40 pin Ceramic Frit-seal DIP with window, Package Mechanical Data mm Symb Typ Min A A1 0.51 A2 3.91 A3 3.89 B 0.41 B1 1.45 – C 0.23 D 51.79 D2 48.26 – E 15.24 – E1 13.06 e 2.54 – eA 14.99 – eB 16.18 L 3.18 S 1.52 8.13 – Figure 10. FDIP40W - 40 pin Ceramic Frit-seal DIP with window, Package Outline ...
Page 13
... M27C1024 inches Min Max – – 0.015 – 0.140 0.154 0.015 0.021 0.045 0.070 0.008 0.012 2.039 2.070 – – 0.583 0.640 0.530 0.551 – – ...
Page 14
... M27C1024 Table 16. PLCC44 - 44 lead Plastic Leaded Chip Carrier, Package Mechanical Data Symbol Typ A 4. 0.33 B1 0.66 D 17.40 D1 16.51 D2 14.99 E 17.40 E1 16.51 E2 14.99 e 1.27 F 0. Figure 12. PLCC44 - 44 lead Plastic Leaded Chip Carrier, Package Outline PLCC Drawing is not to scale. 14/16 mm Min ...
Page 15
... Drawing is not to scale. inches Max Typ Min 1.20 0.15 0.002 1.05 0.037 0.27 0.007 0.21 0.004 14.20 0.543 12.50 0.484 10.10 0.390 – 0.020 0.70 0.020 5 0. M27C1024 Max 0.047 0.006 0.041 0.011 0.008 0.559 0.492 0.398 – – 0.028 0.004 15/16 ...
Page 16
... M27C1024 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice ...