LM77CIMX-3 National Semiconductor, LM77CIMX-3 Datasheet
LM77CIMX-3
Specifications of LM77CIMX-3
Available stocks
Related parts for LM77CIMX-3
LM77CIMX-3 Summary of contents
Page 1
... HVAC applications C® registered trademark of Philips Corporation. © 2010 National Semiconductor Corporation LM77 Features ■ Window comparison simplifies design of ACPI compatible temperature monitoring and control. ...
Page 2
... Simplified Block Diagram Connection Diagram Ordering Information Order Number LM77CIM-3; LM77CIM-3/NOPB LM77CIMX-3; LM77CIMX-3/NOPB LM77CIM-5; LM77CIM-5/NOPB LM77CIMX-5; LM77CIMX-5/NOPB LM77CIMM-3; LM77CIMM-3/NOPB LM77CIMMX-3; LM77CIMMX-3/NOPB LM77CIMM-5; LM77CIMM-5/NOPB LM77CIMMX-5 www.national.com SOP8 or MSOP 10013602 LM77 See NS Package Number M08A or MM08A Supply Voltage Package 3.3V SOP8, M08A 3.3V ...
Page 3
... Pin Descriptions Label Pin # SDA 1 Serial Bi-Directional Data Line. Open Drain Output SCL 2 Serial Bus Clock Input T_CRIT_A 3 Critical Temperature Alarm Open Drain Output GND 4 Power Supply Ground INT 5 Interrupt Open Drain Output +V 8 Positive Supply Voltage Input S A0–A1 7,6 ...
Page 4
... T_CRIT_A and INT Output Voltage Storage Temperature Soldering Information, Lead Temperature Temperature-to-Digital Converter Characteristics Unless otherwise noted, these specifications apply for +V for LM77CIM-3, LM77CIMM-3 (Note otherwise noted. Parameter Accuracy Resolution Temperature Conversion Time Quiescent Current T Default Temperature HYST T Default Temperature LOW T Default Temperature HIGH T ...
Page 5
... Note 10: 9 bits + sign, two's complement Note 11: This specification is provided only to indicate how often temperature data is updated. The LM77 can be read at any time without regard to conversion state (and will yield last conversion result conversion is in process it will be interrupted and restarted after the end of the read. ...
Page 6
... T_CRIT setpoints (e.g HIGH discussion of the function of hysteresis refer to Section 1.1, TEMPERATURE COMPARISON, and Note 14: Default values set at power up. Note 15: Timing specifications are tested at the bus input logic levels (Vin(0)=0.3xVA for a falling edge and Vin(1)=0.7xVA for a rising edge) when the SCL and SDA edge rates are similar ...
Page 7
... For example user never read the part, and temperature went below T then INT would become active. It would stay LOW that way forever if a user never read the part. However if the user read the part, the output would be reset. Even if the condition is true, it will remain reset. The temper- ...
Page 8
... Note: Event Interrupt mode is drawn as if the user is reading the part. If the user doesn't read, the outputs would go low and stay that way until the LM77 is read. 1.4 TEMPERATURE DATA FORMAT Temperature data can be read from the Temperature and Set Point registers; and written to the Set Point registers. Tem- ...
Page 9
... For instance, if the first four bits of the temperature data indicates a critical condition, the host processor could immediately take action to remedy the excessive temperature. At the end of a read, ...
Page 10
FIGURE 4. Inadvertent 8-Bit Read from 16-Bit Register where D7 is Zero (“0”) www.national.com 10 10013608 ...
Page 11
... Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 D3–D15: Temperature Data. One LSB = 0.5°C. Two's com- plement format Fault Queue INT Polarity D4: Fault Queue - When set to 1 the Fault Queue is enabled, see Section 1.7. Power up default of “0”. D5–D7: These bits are used for production testing and must be kept zero for normal operation ...
Page 12
Timing Diagrams Typical 2-Byte Read From Preset Pointer Location Such as Temp or Comparison Registers Typical Pointer Set Followed by Immediate Read for 2-Byte Register such as Temp or Comparison Registers Typical 1-Byte Read from Configuration ...
Page 13
... In Comparator Interrupt Mode, the LM77 simply stops issuing interrupts. The 2nd event is another identical rise in temperature. The 3rd event is typical of a drop in temperature. This is one of the conditions that demonstrates the power of the LM77, as the user receives notification that a lower limit is exceeded in such a way that temperature is dropping ...
Page 14
... Note: Event Interrupt mode is drawn as if the user is reading the part. If the user doesn't read, the outputs would go low and stay that way until the LM77 is read. FIGURE 7. Temperature Response Diagram for ACPI Implementation 4.0 Typical Applications www.national.com FIGURE 8. Typical Application ...
Page 15
... FIGURE 9. Remote HVAC temperature sensor communicates via 3 wires, including thermostat signals. FIGURE 10. ACPI Compatible Terminal Alarm Shutdown. By powering the LM77 from auxilary output of the power supply, a non-functioning overheated computer can be powered down to preserve as much of the system as possible. 15 10013617 10013619 www.national.com ...
Page 16
... Physical Dimensions 8-Lead (0.150 Wide) Molded Small Outline Package (SOP), Order Number LM77CIM-3, LM77CIMX-3, LM77CIM-5 or LM77CIMX-5 8-Lead (0.150 Wide) Molded Mini Small Outline Package (MSOP), Order Number LM77CIMM-3, LM77CIMMX-3, LM77CIMM-5 or LM77CIMMX-5 www.national.com inches (millimeters) unless otherwise noted JEDEC Registration Number MS-012 (variation AA), ...
Page 17
17 www.national.com ...
Page 18
... For more National Semiconductor product information and proven design tools, visit the following Web sites at: www.national.com Products Amplifiers www.national.com/amplifiers Audio www.national.com/audio Clock and Timing www.national.com/timing Data Converters www.national.com/adc Interface www.national.com/interface LVDS www.national.com/lvds Power Management www.national.com/power Switching Regulators www.national.com/switchers LDOs www.national.com/ldo LED Lighting www ...