TDA8543T/N1,518 NXP Semiconductors, TDA8543T/N1,518 Datasheet
TDA8543T/N1,518
Specifications of TDA8543T/N1,518
935227370518
TDA8543TD-T
Related parts for TDA8543T/N1,518
TDA8543T/N1,518 Summary of contents
Page 1
DATA SHEET TDA8543 2 W BTL audio amplifier Product specification INTEGRATED CIRCUITS 1997 Jun 12 ...
Page 2
... NXP Semiconductors 2 W BTL audio amplifier FEATURES • Flexibility in use • Few external components • Low saturation voltage of output stage • Gain can be fixed with external resistors • Standby mode controlled by CMOS compatible levels • Low standby current • No switch-on/switch-off plops • ...
Page 3
... NXP Semiconductors 2 W BTL audio amplifier BLOCK DIAGRAM handbook, halfpage PINNING SYMBOL PIN n.c. 1 not connected n.c. 2 not connected MODE 3 operating mode select (standby, mute, operating) SVR 4 half supply voltage, decoupling ripple rejection IN+ 5 positive input IN− 6 negative input n.c. 7 not connected n ...
Page 4
... NXP Semiconductors 2 W BTL audio amplifier FUNCTIONAL DESCRIPTION The TDA8543( BTL audio power amplifier capable of delivering an output power between 1 and 2 W, depending on supply voltage, load resistance and package. Using the MODE pin the device can be switched to standby and mute condition. The device is protected by an internal thermal shutdown protection mechanism ...
Page 5
... NXP Semiconductors 2 W BTL audio amplifier handbook, halfpage (1) DIP16. (2) SO16. Table 1 V (V) R (Ω 7 Note 1. At THD = 10%; BTL. 1997 Jun 12 2.5 P (W) 2.0 1.5 (1) 1 (2) 0 Fig.3 Power derating curve. ( max 1.2 2.2 1.4 2.0 1.3 5 Product specification ...
Page 6
... NXP Semiconductors 2 W BTL audio amplifier DC CHARACTERISTICS = 25 ° Ω amb L SYMBOL PARAMETER V supply voltage CC I quiescent current q I standby current stb V DC output voltage O ⎪V − V ⎪ differential output voltage offset OUT+ OUT− input bias current IN+ IN− V input voltage mode select ...
Page 7
... NXP Semiconductors 2 W BTL audio amplifier Notes to the AC characteristics R2 × 1. Gain of the amplifier is 2 ------- - R1 2. The noise output voltage is measured at the output in a frequency range from kHz (unweighted), with = 0 Ω at the input. a source impedance Supply voltage ripple rejection is measured at the output, with a source impedance of R The ripple voltage is a sine wave with a frequency of 1 kHz and an amplitude of 100 mV (RMS), which is applied to the positive supply rail ...
Page 8
... NXP Semiconductors 2 W BTL audio amplifier BTL APPLICATION handbook, full pagewidth μF 11 kΩ μF R2 × ------- - Gain = handbook, halfpage I q (mA ∞ Fig function 1997 Jun 12 56 kΩ − TDA8543 SVR 4 MODE GND Fig.4 BTL application. MGD876 handbook, halfpage ( 100 μF 100 nF OUT − ...
Page 9
... NXP Semiconductors 2 W BTL audio amplifier 10 handbook, halfpage THD (%) 1 (1) (2) −1 10 − 0 dB Ω. ( Ω Ω. ( Fig.7 THD as a function of frequency. 2.5 handbook, halfpage P o (W) 2 (1) 1 THD = 10 Ω. ( Ω. ( Ω. ( Fig function 1997 Jun 12 MGK409 handbook, halfpage SVRR (dB) ...
Page 10
... NXP Semiconductors 2 W BTL audio amplifier 2 handbook, halfpage P (W) (3) 1.6 (1) 1.2 0.8 (2) 0 0.5 1 Sine wave of 1 kHz Ω. ( Ω. ( Ω Fig. function handbook, halfpage V ms (V) 12 standby Fig. function 1997 Jun 12 MGK407 handbook, halfpage 1 MGL070 mute operating (V) ...
Page 11
... NXP Semiconductors 2 W BTL audio amplifier SE APPLICATION handbook, full pagewidth μF 11 kΩ μF R2 Gain = ------- - R1 10 handbook, halfpage THD (%) 1 (1) (2) −1 10 (3) −2 10 −2 − kHz dB Ω Ω. ( Ω. ( Fig.15 THD as a function of P 1997 Jun 12 110 kΩ − TDA8543 SVR ...
Page 12
... NXP Semiconductors 2 W BTL audio amplifier −20 handbook, halfpage SVRR (dB) −40 (1) (2) −60 (3) − Ω Ω 7 100mV ( dB dB dB. v Fig.17 SVRR as a function of frequency. 1.6 handbook, halfpage P (W) 1.2 (1) (2) 0.8 0 Ω. ( Ω. ( Ω. ( Fig.19 Worst case power dissipation as a function of V ...
Page 13
... NXP Semiconductors 2 W BTL audio amplifier handbook, full pagewidth 1997 Jun 12 a. Top view. 10 kΩ kΩ 1 TDA8543 IN 1 μF 11 kΩ μF 100 μF b. Component side. Fig.21 Printed-circuit board layout (BTL and SE). 13 Product specification 16 OUT + 9 56 kΩ OUT − ...
Page 14
... NXP Semiconductors 2 W BTL audio amplifier PACKAGE OUTLINES DIP16: plastic dual in-line package; 16 leads (300 mil); long body pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions UNIT max. min. max. mm 4.7 0.51 3.7 inches 0.19 0.02 0.15 Note 1 ...
Page 15
... NXP Semiconductors 2 W BTL audio amplifier SO16: plastic small outline package; 16 leads; body width 3 pin 1 index 1 DIMENSIONS (inch dimensions are derived from the original mm dimensions) A UNIT max. 0.25 1.45 mm 1.75 0.25 0.10 1.25 0.010 0.057 inches 0.069 0.01 0.004 0.049 Note 1 ...
Page 16
... NXP Semiconductors 2 W BTL audio amplifier SOLDERING Introduction There is no soldering method that is ideal for all IC packages. Wave soldering is often preferred when through-hole and surface mounted components are mixed on one printed-circuit board. However, wave soldering is not always suitable for surface mounted ICs, or for printed-circuits with high population densities ...
Page 17
... In no event shall NXP Semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the ...
Page 18
... NXP Semiconductors’ specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies NXP Semiconductors for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NXP Semiconductors’ ...
Page 19
... Interface, Security and Digital Processing expertise Customer notification This data sheet was changed to reflect the new company name NXP Semiconductors, including new legal definitions and disclaimers. No changes were made to the technical content, except for package outline drawings which were updated to the latest version. ...