ICX084AL Sony, ICX084AL Datasheet
ICX084AL
Related parts for ICX084AL
ICX084AL Summary of contents
Page 1
... Diagonal 6mm (Type 1/3) Progressive Scan CCD Image Sensor with Square Pixel for B/W Cameras Description The ICX084AL is a diagonal 6mm (Type 1/3) interline CCD solid-state image sensor with a square pixel array which supports VGA format. Progressive scan allows all pixels signals to be output independently within approximately 1/30 second ...
Page 2
... Reset gate clock H Horizontal register transfer clock 1 H Horizontal register transfer clock 2 Ratings Unit –0.3 to +36 V –0.3 to +18 V – – +16 V –16 to +16 V –10 to +15 V –55 to +10 V –65 to +0.3 V –0.3 to +27.5 V –0.3 to +20.5 V –0.3 to +17.5 V –30 to +80 °C –10 to +60 °C ICX084AL Remarks 2 ...
Page 3
... Typ. Max. Unit Remarks 15.0 15. Unit Remarks mA Waveform Unit Remarks diagram High-level coupling V 2 High-level coupling V 2 Low-level coupling V 2 Low-level coupling Input through 0.01µ capacitance V 4 Low-level coupling ICX084AL V L VH02 + V )/2 VL1 VL3 ...
Page 4
... Vertical transfer clock equivalent circuit Reset gate clock equivalent circuit Symbol V12 C V23 C V31 SUB GND Horizontal transfer clock equivalent circuit C RG – 4 – Min. Typ. Max. Unit Remarks 560 pF 470 pF 1500 pF 1500 pF 1500 pF 1000 570 pF Ω 20 Ω 56 Ω 43 Ω Ω ICX084AL H 2 ...
Page 5
... V VHL V VL01 VH02 VL03 VL3 twh tf V VH1 V VHH V VLH V VL1 V VLL V VH2 V VHH V VHL V VLH V VL2 V VLL V VH3 V VHH V VHL V VLH V VLL = V VH02 = ( )/2 VL01 VL03 = V VL03 – 5 – and – VH1 VL01 – VH02 VL2 – VH3 VL03 ICX084AL ...
Page 6
... CCD) tr twh twl Point A is the minimum value of the coupling waveform during the period from RGLL t wh, then: 100% 90% V SUB 10 twh – 6 – twl tr twh tf V RGH RGL V RGL is the average value of V RGL ICX084AL + 0.5V and RGLH ...
Page 7
... H rising side of the two Unit Remarks horizontal transfer clocks H – 7 – Unit 0.5 0.5 µs During readout 15 350 ns 10 17 0.01 µs 0. During drain 0.5 0.5 µs charge and H waveforms must and H is two ICX084AL Remarks 1 2 ...
Page 8
... Note) Adjust the amplifier gain so that the gain between [ A] and [ B] equals 1. Min. Typ. Max. Unit 540 700 mV 500 mV 0.005 0.015 % 0 494 (V) Zone Zone II, II' Ignored region Effective pixel region S/H C.D.S AMP – 8 – ICX084AL (Ta = 25°C) Measurement method Remarks 60° Zone 0 and 4 Zone 60° 60°C 7 Signal output [ B] I ...
Page 9
... Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60°C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference color temperature of 3200K halogen source subject the center of the screen, and substitute the value into the S 100 [%] (1/10V method conversion value) – 9 – ICX084AL ...
Page 10
... Adjust the signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) 100 [%] VD V2 Strobe light timing Output Light Signal output 150mV Vlag (Lag) – 10 – ICX084AL ...
Page 11
... ICX084AL ...
Page 12
... Sensor Readout Clock Timing Chart XSG XV1 XV2 XV3 HD 42.4µs (520 bits 600 700 800 Wave Length [nm] Sensor readout clock XSG is used by composing XV2 and XV3. 2.53µs (31 bits) 2.04µs (25 bits) – 12 – ICX084AL 900 1000 ...
Page 13
... ICX084AL ...
Page 14
... ICX084AL ...
Page 15
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the bottom of the package. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 50N 50N Compressive strength – 15 – ICX084AL 1.2Nm Torsional strength ...
Page 16
... Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. c) The brown stain may be seen on the bottom or side of the package. But this does not affect the CCD characteristics. – 16 – ICX084AL ...
Page 17
... ICX084AL ...