LA1231N Sanyo Semiconductor Corporation, LA1231N Datasheet

no-image

LA1231N

Manufacturer Part Number
LA1231N
Description
FM IF system
Manufacturer
Sanyo Semiconductor Corporation
Datasheet
Ordering number : EN660A
Overview
Being developed for FM IF System, LA1231 is a highly
integrated circuit in which almost all functions are
contained concerning the FM tuner IF stage. The block
diagram of equivalent circuit is shown below. Usual
peripheral circuits are shown also in examples of
application circuits.
The IF amplifier and limiter stages are composed of 6-
stage double-end type differential amplifier, which is
superior on its AMR. The signal meter driving stage which
is located in parallel therewith consists of a 3-stage level
detector circuit and a drive circuit in order to extend the
linear area.
The FM detection stage composed of a double-balance type
quadrature detecting circuit is attached with a low frequency preamplifier and muting control circuit.
The muting drive stage is composed of the following 3 circuits.
1) A level detection circuit which detects the S/N ratio of carrier wave when the input is weak.
2) A circuit which detects the dc output of FM detector's 'S' curve when detuning is made.
3) A driving circuit.
Thus, this muting driving stage can reduce foreign factors such as the interstation noises, the shock noise caused from
muting when detuning is made, and so forth.
Besides, a voltage-inverting circuit is built in LA1231N so that the muting may be enabled at any appropriate input signal
level. The output of this voltage-inverting circuit is connected with the muting drive output terminal. Thus, the muting can
be placed to the ON or OFF status when a control voltage is applied from other section to the input terminal of the voltage-
inverting circuit. For the control voltage, the output of the signal meter driver is appropriate. Both the AFC output stage
and tuning meter driving stage are of the current-driven type. So, not only the sensitivity of AGC but also the muting band
(when detuning is made) can be controlled by an outer resistor.
Being utilized for disabling the FM IF amplifier when AM reception is made, the IF amplification/stop circuit can decrease
the shock noise caused at the conversion between FM and AM reception modes.
Functions
• IF amplification, Limiter.
• AF preamplifier.
• Muting at the detuning.
• AFC tuning meter drive output.
• Inverting circuit for muting drive voltage.
SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN
• Quadrature detection.
• Muting at weak.
• Signal meter drive output.
• Delay AGC output.
• IF amplifier stop circuit.
Package Dimensions
unit: mm
3006B-DIP16
O2097HA (KT)/8044/D040KI No.660-1/8
[LA1231N]
FM IF System
Monolithic Linear IC
LA1231N
SANYO: DIP16

LA1231N Summary of contents

Page 1

... Thus, this muting driving stage can reduce foreign factors such as the interstation noises, the shock noise caused from muting when detuning is made, and so forth. Besides, a voltage-inverting circuit is built in LA1231N so that the muting may be enabled at any appropriate input signal level. The output of this voltage-inverting circuit is connected with the muting drive output terminal. Thus, the muting can be placed to the ON or OFF status when a control voltage is applied from other section to the input terminal of the voltage- inverting circuit ...

Page 2

... I CC Maximum flow-in current Maximum flow-out current Allowable power dissipation Pd max Operating temperature Topr Storage temperature Tstg LA1231N Voltage regulator Guadrature limiter IF amp/limiter Guadrature det Level Level Level Level DC det det det det det level Signal meter Mute drive drive Conditions ...

Page 3

... V 16 Offset voltage V 6- 7-10 B Pin voltage LA1231N at Ta=25°C Conditions CC at Ta=25°C, V =12V, f=10.7MHz CC Conditions V =100dBµ =100dBµ, 400Hz-100% mod IN V =100dBµ, 400Hz-100% mod IN Vo 3dB down, 400Hz-100% mod V =100dBµ, 400Hz-100% mod IN V =1. =2V, V =100dBµ, 5 ...

Page 4

... Test Circuit DC characteristics AC characteristics LA1231N Pd max – Ta Ambient temperature, Ta – °C Unit (resistance : Ω, capacitance : F) Unit (resistance : Ω, capacitance : F) No.660-4/8 ...

Page 5

... Sample Application Circuit LA1231N No.660-5/8 ...

Page 6

... LA1231N IF input voltage, V – dBµ IN – ∆f V 7-10 Detuning frequency, ∆f – kHz Mute(att) – Pin voltage, V – Pin voltage, V – Pin Voltage – input voltage, V – dBµ IN – ∆ Detuning frequency, ∆f – kHz Unit (resistance : Ω, capacitance : µF) Quadrature signal, V – ...

Page 7

... LA1231N I (IF off) – input voltage, V – dBµ (lim) – Generator resistance, Rg – Ω Ambient temperature, Ta – °C Ambient temperature, Ta – °C Resistance between pin – kΩ 7-10 V (mute), V (lim) – Ambient temperature, Ta – °C Ambient temperature, Ta – °C Ambient temperature, Ta – °C ...

Page 8

... SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of October, 1997. Specifications and information herein are subject to change without notice. LA1231N Ambient temperature, Ta – °C Supply voltage, V – ...

Related keywords