MACH211-7VC Lattice Semiconductor Corp., MACH211-7VC Datasheet
MACH211-7VC
Available stocks
Related parts for MACH211-7VC
MACH211-7VC Summary of contents
Page 1
FEATURES High-performance electrically-erasable CMOS PLD families 32 to 128 macrocells 44 to 100 pins in cost-effective PLCC, PQFP and TQFP packages SpeedLocking™ – guaranteed fixed timing product terms Commercial 5/5.5/6/7.5/10/12/15-ns t Configurable macrocells — Programmable polarity — ...
Page 2
... Leaded Chip Carrier (PLCC) packages from 44 to 100 pins (Table 3). Each MACH 1 & 2 device is PCI compliant and includes other features such as SpeedLocking architecture for guaranteed fixed timing, Bus-Friendly inputs and I/Os, and programmable power-down mode for extra power savings. 2 MACH131 (SP) MACH211 (SP ...
Page 3
... MACH111 X MACH111SP X MACH131 MACH131SP MACH211 X MACH211SP X MACH221 MACH221SP MACH231 MACH231SP Note: 1. The MACH110, MACH120, MACH130, MACH210, MACHLV210, MACH215, MACH220 and MACH230 are not listed above and not recommended for new designs. However, they are still supported by Lattice/Vantis. For technical or sales support, please call your local Lattice/Vantis sales offi ...
Page 4
... There are no buried macrocells in MACH 1 devices. All macrocells are output macrocells. Device PAL Blocks MACH111(SP) 2 MACH131(SP) 4 MACH211(SP) 4 MACH221(SP) 8 MACH231(SP) 8 Figure 1. Overall Architecture of MACH 1 & 2 Devices The switch matrix takes all dedicated inputs and signals from the input switch matrices and routes them as needed to the PAL blocks ...
Page 5
... The product term clusters do not “wrap” around the logic block. This means that the macrocells at the ends of the block have fewer product terms available (Tables 8). Table 4. PAL Block Inputs Device MACH211SP 26 MACH221 26 26 MACH221SP ...
Page 6
Product Term Cluster Figure 2. Product Term Clusters and the Logic Allocator Table 5. Logic Allocation for MACH111(SP) Output Macrocell Table 6. Logic Allocation ...
Page 7
... Table 7. Logic Allocation for MACH211(SP) and MACH231(SP) Macrocell Output Buried Available Clusters Table 8. Logic Allocation for MACH221(SP) Macrocell Output Buried Available Clusters Macrocell There are two fundamental types of macrocell: the output macrocell and the buried macrocell. The buried macrocell is only found in MACH 2 devices. The use of buried macrocells effectively doubles the number of macrocells available without increasing the pin count ...
Page 8
The output macrocell (Figure 3) sends its output back to the switch matrix, via internal feedback, and to the I/O cell. The feedback is always available regardless of the configuration of the I/O cell. This allows for buried combinatorial or ...
Page 9
From n Logic Allocator To Switch Matrix a. Combinatorial, active high From Logic Allocator CLK 0 AR CLK n To Switch Matrix c. D-type register, active high From Logic n AP Allocator T CLK 0 AR ...
Page 10
PAL-Block Asynchronous Preset Sum of Products From Logic IC Allocator CLK 0 CLK n PAL-Block Asynchronous Reset Switch Matrix From n Logic Allocator To Switch Matrix a. Combinatorial n From Logic Allocator CLK 0 CLK n To Switch Matrix c. ...
Page 11
... The two product terms provided are common to a bank of I/O cells. Table 10. Macrocell Clocks Device MACH211SP 4 2 MACH221 4 ...
Page 12
Output Enable Product Terms (Common to bank of I/O Cells) SPEEDLOCKING FOR GUARANTEED FIXED TIMING The unique MACH 1 & 2 architecture is designed for high performance—a metric that is met in both raw speed, and even more importantly, guaranteed ...
Page 13
JTAG IN-SYSTEM PROGRAMMING Programming devices in-system provides a number of significant benefits including: rapid prototyping, lower inventory levels, higher quality, and the ability to make in-field modifications. All MACHxxxSP devices provide in-system programming (ISP) capability through their JTAG ports. This ...
Page 14
V rise must be monotonic and the clock must be inactive until the reset CC delay time has elapsed. SECURITY BIT A security bit is provided on the MACH devices as a deterrent to unauthorized copying of ...
Page 15
MACH111(SP) AND MACH131(SP) PAL BLOCK Switch Matrix for MACH111, MACH131, MACH131SP Output Enable Output Enable 24 ...
Page 16
... MACH211(SP) PAL BLOCK Switch Matrix MACH 1 & 2 Families Output Enable Output Enable Asynchronous Reset Asynchronous Preset I/O I/O Cell Output Macro M Cell 0 Buried Macro M Cell 1 I/O I/O Cell Output M Macro 2 Cell Buried Macro M Cell 3 I/O Cell I/O C Output 0 M Macro 4 Cell ...
Page 17
MACH221(SP) PAL BLOCK Switch Matrix MACH 1 & ...
Page 18
MACH231(SP) PAL BLOCK Switch Matrix ...
Page 19
BLOCK DIAGRAM (MACH111, MACH111SP CLK CLK CLK CLK Block A CLK I/O – I/O CLK I/O Cells 16 16 Macrocells AND Logic Array and Logic Allocator 26 Switch Matrix ...
Page 20
BLOCK DIAGRAM (MACH131, MACH131SP) Block A I/O – I I/O Cells 16 4 Macrocells AND Logic Array and Logic Allocator AND Logic Array and Logic Allocator OE Macrocells 4 ...
Page 21
... BLOCK DIAGRAM (MACH211, MACH211SP) Block A I/O –I I/O Cells Macrocells Macrocells AND Logic Array and AND Logic Array and Logic Allocator OE 2 Macrocells Macrocells I/O Cells 8 I/O –I Block D Block B MACH211 only I/O –I I/O Cells Macrocells Macrocells AND Logic Amrray ...
Page 22
BLOCK DIAGRAM (MACH221, MACH221SP) 22 MACH 1 & 2 Families 14051K-011 ...
Page 23
BLOCK DIAGRAM (MACH231, MACH231SP) MACH 1 & 2 Families 14051K-012 23 ...
Page 24
... Output Short-Circuit Current SC Notes: 1. This applies to MACH111SP, MACH131SP, and die code “B” or later for MACH211(SP) and MACH231(SP). This does not apply to MACH111, MACH131, MACH221(SP), and die code “A” for MACH211(SP) and MACH231(SP). 2. Total I for one PAL block should not exceed 64 mA. ...
Page 25
MACH111 AND MACH111SP SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Parameter Description Symbol t Input, I/O, or Feedback to Combinatorial Output PD Setup Time from Input, I/O, or Feedback Clock t Register Data Hold Time H t Clock ...
Page 26
MACH131 AND MACH131SP SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Parameter Description Symbol t Input, I/O, or Feedback to Combinatorial Output PD t Setup Time from Input, I/O, or Feedback S t Hold Time H t Clock to Output CO t ...
Page 27
... MACH211 AND MACH211SP SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Symbol Parameter Description Input, I/O, or Feedback to Combinatorial t PD Output Setup Time from Input, I/O, or Feedback Clock t Register Data Hold Time H t Clock to Output Clock Width t WH External 1/( Feedback Maximum f MAX Frequency Internal Feedback (f ...
Page 28
... These parameters are not 100% tested, but are evaluated at initial characterization and at any time the design is modified where this parameter may be affected signal is powered-down, this parameter must be added to its respective high-speed parameter. 4. MACH211 ns. MACH211SP MACH211, commercial ns The faster - apply to MACH211 only, not MACH211SP. GO PDL ICO -10 Min Max Min Max Min Max 9 9 ...
Page 29
MACH221 and MACH221SP SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Symbol Parameter Description t Input, I/O, or Feedback to Combinatorial Output PD Setup Time from Input, I/O, or Feedback Clock t Register Data Hold Time H t Clock ...
Page 30
MACH221 and MACH221SP (CONTINUED) SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Symbol Parameter Description t Asynchronous Preset Width (Note 3) APW t Asynchronous Preset Recovery Time (Note 3) APR t Input, I/O, or Feedback to Output Enable EA t Input, I/O, ...
Page 31
MACH231 AND MACH231SP SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Symbol Parameter Description t Input, I/O, or Feedback to Combinatorial Output PD Setup Time from Input, I/O, or Feedback Clock t Register Data Hold Time H t Clock ...
Page 32
MACH231 AND MACH231SP (CONTINUED) SWITCHING CHARACTERISTICS OVER OPERATING RANGES Parameter Symbol Parameter Description t Input Latch Gate Width LOW WIGL Input, I/O, or Feedback to Output Through t PDLL Transparent Input and Output Latches Asynchronous Reset to Registered or Latched ...
Page 33
... The selected “typical” pattern is a 16-bit up-down counter. This pattern fills the device and exercises every macrocell. Maximum frequency shown uses internal feedback and a D-type register. MACH111(SP) 150 125 100 Frequency (MHz) MACH211(SP) 150 125 100 Frequency (MHz) MACH231 400 350 ...
Page 34
... Device Parameter Symbol MACH111(SP) MACH211(SP) MACH221(SP) MACH131(SP) MACH231SP MACH231 MACH111(SP) MACH211(SP) MACH221(SP) MACH131(SP) MACH231SP MACH231 34 Table 12 Parameter Description Supply Current (Static Supply Current (Active) MACH 1 & 2 Families Test Description Typ Unit 5V 25° MHz 80 135 5V 25° MHz 100 150 ...
Page 35
PIN PLCC CONNECTION DIAGRAM (MACH111-5/7/10/12/15 AND MACH111SP-5/7/10/12/15) Top View I/O5 I/O6 I/O7 (TDI) I0 (CLK 0/I0) CLK0/I1 Block A GND (TCK) CLK1/I2 I/O8 I/O9 I/O10 I/O11 PIN DESIGNATIONS CLK/I = Clock or Input GND = Ground I = Input ...
Page 36
TQFP CONNECTION DIAGRAM MACH111SP-5/7/10/12/15) Top View I/O5 I/O6 I/O7 (TDI) I0 (CLK 0/I0) CLK0/I1 Block A GND (TCK) CLK1/I2 I/O8 I/O9 I/O10 I/O11 PIN DESIGNATIONS CLK/I = Clock or Input GND = Ground I = Input I/O = Input/Output ...
Page 37
PLCC CONNECTION DIAGRAM (MACH131-5/7/10/12/15) Top View Block I/O8 I/O9 13 I/O10 14 I/O11 15 I/O12 16 I/O13 17 I/O14 18 I/O15 19 CLK0/I0 20 VCC 21 GND 22 CLK1/I1 23 I/O16 24 I/O17 25 I/O18 ...
Page 38
PQFP CONNECTION DIAGRAM (MACH131SP-5/7/10/12/15) Top View Block A 1 GND GND 2 TDI I/ I/O9 7 I/O10 I/O11 8 9 I/O12 10 I/O13 11 I/O14 12 I/O15 13 IO/CLK0 ...
Page 39
TQFP CONNECTION DIAGRAM (MACH131SP-5/7/10/12/15) Top View Block A TDI 1 I/5 2 I/O8 3 I/O9 4 I/O10 5 I/O11 6 I/O12 7 I/O13 8 I/O14 9 I/O15 10 I0/CLK0 GND 13 GND 14 I1/CLK1 15 ...
Page 40
... Top View Block A I/O5 I/O6 I/O7 (TDI (CLK 0/I0) CLK0/I1 GND (TCK) CLK1/I2 I/O8 I/O9 I/O10 I/O11 Block B PIN DESIGNATIONS CLK/I = Clock or Input GND = Ground I = Input I/O = Input/Output V = Supply Voltage CC Note: 1. Pin designators in parentheses ( ) apply to the MACH211SP 40 44-Pin PLCC TDI = Test Data In ...
Page 41
... Top View Block A I/O5 I/O6 I/O7 (TDI) I0 (CLK 0/I0) CLK0/I1 GND (TCK) CLK1/I2 I/O8 I/O9 I/O10 I/O11 Block B PIN DESIGNATIONS CLK/I = Clock or Input GND = Ground I = Input I/O = Input/Output V = Supply Voltage CC Note: 1. Pin designators in parentheses ( ) apply to the MACH211SP 44-Pin TQFP Block Block C ...
Page 42
PLCC CONNECTION DIAGRAM (MACH221-7/10/12/15) Top View I/O7 I/O8 I/O9 I/O10 I/O11 CLK0/I0 CLK1/I1 I2 VCC GND I3 I/O12 I/O13 I/O14 I/O15 I/O16 I/O17 PIN DESIGNATIONS CLK/I = Clock or Input GND = Ground I = Input I/O = Input/Output ...
Page 43
PQFP CONNECTION DIAGRAM (MACH221SP-7/10/12/15) Top View 1 GND GND 2 TDI N N/C 8 I/O7 9 I/O8 I/ I/O10 12 I/O11 13 IO/CLK0 GND ...
Page 44
PLCC CONNECTION DIAGRAM (MACH231-6/7/10/12/15) Top View I/O8 13 I/O9 I/O10 14 I/O11 15 16 I/O12 17 I/O13 18 I/O14 I/O15 19 CLK GND CLK ...
Page 45
PQFP CONNECTION DIAGRAM (MACH231SP-10/12/15) Top View 1 GND GND 2 TDI I/ I/O10 8 I/O11 9 I/O12 I/O13 10 11 I/O14 12 I/O15 13 IO/CLK0 GND ...
Page 46
TQFP CONNECTION DIAGRAM (MACH231SP-10/12/15) Top View TDI I/O8 3 I/O9 4 I/O10 5 I/O11 6 I/O12 7 I/O13 8 I/O14 9 I/O15 10 I0/CLK0 GND 13 GND 14 I1/CLK1 15 I/O16 16 ...
Page 47
... Y C Valid Combinations – Industrial MACH111 JC, VC JC, VC MACH111SP MACH131 JC/1 MACH131SP VC, YC MACH211 JC, VC MACH211SP JC, VC MACH221 JC MACH221SP YC MACH231 JC MACH231SP JC/1 VC, YC The Valid Combinations list configurations planned to be supported in volume for this device. Consult the local Lattice/ Vantis sales office to confirm availability of specific valid combinations and to check on newly released combinations. MACH 1 & ...
Page 48
MACH 1 & 2 Families ...