KTS6027-2 Infineon Technologies AG, KTS6027-2 Datasheet
KTS6027-2
Related parts for KTS6027-2
KTS6027-2 Summary of contents
Page 1
... Wireless Components 2 Band TV Tuner Mixer-Oscillator-PLL with unbalanced IF-Amplifier KTS6027-2, KTS6029-2 Version 2.0 Specification July 2001 ...
Page 2
... Components used in life-support devices or systems must be expressly authorized for such purpose! 1 Critical components of the Infineon Technologies AG, may only be used in life-support devices or systems Infineon Technologies AG critical component is a component used in a life-support device or system whose failure can reasonably be expected to cause the failure of that life- support device or system affect its safety or effectiveness of that device or system ...
Page 3
... Product Info General Description The KTS6027-2/KTS6029 mixer/oscillator and synthesizer for analog and digital TV and VCR tuners. Features General Suitable for analog and digital ter- restrial TV tuner Compatible with KTS6027-S or KTS6029-S in normal mode New features in extended mode Full ESD protection ...
Page 4
... Internal Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10 3.3 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15 3.4 Circuit Description 3-16 4 Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19 4.1 KTS6027-2 Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 4.2 KTS6029-2 Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 5 Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-22 5.1 Electrical Data 5-23 5.1.1 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-23 5.1.2 Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25 5 ...
Page 5
Product Description Contents of this Chapter 2.1 General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 6
... General Description The KTS6027-2, KTS6029-2 device combines a digitally programmable phase locked loop (PLL), with a mixer-oscillator block including two balanced mixers and oscillators for use in TV and VCR tuners. The PLL block with four selectable chip addresses forms a digitally programm- able phase locked loop. With a 4 MHz quartz crystal, the PLL permits precise setting of the frequency of the tuner oscillator up to 1024 MHz in increments of 31 ...
Page 7
... Application The IC is suitable for NTSC tuners in TV- and VCR-sets or CATV set-top receivers for analog TV and Digital Video Broadcasting. 2.4 Package Outlines P-TSSOP-28-1 Wireless Components KTS6027-2, KTS6029 Product Description Specification, July 2001 ...
Page 8
Functional Description Contents of this Chapter 3.1 Pin Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 9
... Wireless Components OSCHIGHIN 1 OSCHIGHOUT 2 OSCHIGHOUT 3 OSCHIGHIN 4 OSCLOW/MIDIN 5 OSCLOW/MIDOUT 6 7 OSCLOW/MIDOUT KTS6027-2 8 OSCLOW/MIDIN RFGND 9 ADC 10 IFOUT 11 PHIGH KTS6027-2 Pin Configuration HIGHIN 1 2 HIGHIN 3 LOW/MIDIN 4 VCC 5 MIXOUT 6 MIXOUT 7 PLLGND KTS6029-2 8 SDA 9 SCL AS 10 XTAL 11 PFM 12 13 PMID 14 PLOW KTS6029-2 Pin Configuration ...
Page 10
... Internal Pin Configuration Note: Pin designation refers to KTS6027-2. KTS6029-2 has reversed pinning Table 3-1 Pin Definition and Function Pin No. Symbol 1 OSCHIGHIN 2 OSC- HIGHOUT 3 OSC- HIGHOUT 4 OSCHIGHIN 5 OSCLOW/ MIDIN 6 OSCLOW/ MIDOUT 7 OSCLOW/ MIDOUT 8 OSCLOW/ MIDIN 9 RFGND analog ground Wireless Components Equivalent I/O-Schematic ...
Page 11
... Table 3-1 Pin Definition and Function (continued) Pin No. Symbol 10 ADC 11 IFOUT 12 PHIGH Wireless Components Equivalent I/O-Schematic KTS6027-2, KTS6029-2 Functional Description Average DC voltage LOW/MID HIGH V V ADC ADC 2.3 V 2 Specification, July 2001 ...
Page 12
... Pin No. Symbol PLOW 16 PMID 17 PFM 18 XTAL Wireless Components Equivalent I/O-Schematic KTS6027-2, KTS6029-2 Functional Description Average DC voltage LOW/MID HIGH 2 3.0 V 3.0 V Specification, July 2001 ...
Page 13
... Table 3-1 Pin Definition and Function (continued) Pin No. Symbol SCL 21 SDA 22 PLLGND digital ground Wireless Components Equivalent I/O-Schematic KTS6027-2, KTS6029-2 Functional Description Average DC voltage LOW/MID HIGH n.a. n.a. n.a. n.a. 0.0 V 0.0 V Specification, July 2001 ...
Page 14
... Table 3-1 Pin Definition and Function (continued) Pin No. Symbol 23 MIXOUT 23 24 MIXOUT 25 VCC supply voltage 26 LOW/MIDIN 27 HIGHIN 28 HIGHIN Wireless Components Equivalent I/O-Schematic IF Amp KTS6027-2, KTS6029-2 Functional Description Average DC voltage LOW/MID HIGH 3 3.8 V 3.8 V Oscillator 5.0 V 5.0 V 1.8 V 0.0 V 0 0.0 V 0.9 V Specification, July 2001 ...
Page 15
... I C Bus FL Lock Detector Mixer ADC Prog. Divider SAW Driver (24) (23) (22) (21) (20 Block Diagram KTS6027-2, KTS6029-2 Functional Description (11) (12) (13) (14) Ports Crystal Oscillator Reference Divider f f div ref Phase/ Frequency Comparator CP, CM, Charge OS Pump ...
Page 16
... VCO Wireless Components see Table 5-7 Test modes on page 32 see Table 5-8 Reference divider ratio on page 32 see Table 5-9 Charge pump current on page KTS6027-2, KTS6029-2 Functional Description ) the IC is compatible with ) and two additional charge pump ) available. = 31.25, 50, 62.5 or ...
Page 17
... I lator frequency and C1, C2 the capacitances in the loop filter ( KTS6027-2 Evaluation Board on page takes a maximum for reset after the loop has lost lock ref state ...
Page 18
... SDA line to LOW, which would block the bus. The power-on reset flag POR is set at power-on and when V at the end of a READ operation. Wireless Components KTS6027-2, KTS6029-2 Functional Description see Table 5-4 Bit Allocation Read / Write on page 31 ). falls below 3 will be reset ...
Page 19
... Applications Contents of this Chapter 4.1 KTS6027-2 Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-20 4.2 KTS6029-2 Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21 ...
Page 20
... KTS6027-2 Evaluation Board Gen Gen HIGH V LOW / MID 4n7 1:1*) 1n 22p 22p 2p2 1p2 1p2 1p2 1p2 L1 18p 1k8 1k8 BB659C 10n Figure 4-1 Table 4-1 Recommended band limits in MHz RF input min max LOW 55.25 127.25 MID 133.25 361.25 HIGH 367 ...
Page 21
... CC SDA SCL AS KTS6029-2 Evaluation Board Table 4-1 Coils Oscillator min max L1 101 173 L2 179 407 L3 413 849 KTS6027-2, KTS6029-2 Applications + 33 V 4n7 33k 560 220 C PHIGH 2 2n2 C 4n7 1 47n 18p 4 MHz 4n7 ...
Page 22
Reference Contents of this Chapter 5.1 Electrical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 23
... I 5 SDA(L) V -0.3 6 SCL -0.3 V ADC KTS6027-2, KTS6029-2 Reference Amax Unit Remarks open collector 0.1 sec. max at 5 0.1 sec. max at 5.5 V Specification, July 2001 ...
Page 24
... According to EIA/JESD22-A114-B (HBM incircuit test single device incircuit contact discharge test. Wireless Components = - 20°C ... + 85°C (continued) AMB Symbol Limit Values Unit min max ESD KTS6027-2, KTS6029-2 Reference Remarks Specification, July 2001 ...
Page 25
... Absolute Maximum Ratings on page 23 Wireless Components Symbol Limit Values Unit min max V +4.5 +5 256 32767 f 40 500 MHz i f 350 900 MHz 560 MHz O f 380 950 MHz O T -20 T AMB Amax 1 KTS6027-2, KTS6029-2 Reference Test Conditions Specification, July 2001 Item ...
Page 26
... V 10 µ µA -10 µ KTS6027-2, KTS6029-2 Reference Test Conditions L Item LOW/MID band HIGH band series resonance series resonance MHz XTAL MHz XTAL VCP = 1.8 V VCP = 1.8 V VCP = 1.8 V VCP = 1.8 V T0=1, T1=0 PLL locked ...
Page 27
... V 10 µA -10 µA 50 µA -50 µ KTS6027-2, KTS6029-2 Reference Test Conditions L Item POH POL ASH ASL Specification, July 2001 ...
Page 28
... KTS6027-2, KTS6029-2 Reference Test Conditions L Item f = 55.25 to 361.25 RF MHz 41, 58.75 MHz f = 55.25 to 361.25 RF MHz f = 55.25 MHz RFw f = 361.25 MHz RFw f = 55.25 MHz RF1 f = 111 ...
Page 29
... KTS6027-2, KTS6029-2 Reference Test Conditions L Item kHz f = 55.25 MHz kHz f = 361.25 MHz 10kHz dBµ 367.25 MHz to RF 801.25 MHz, f ...
Page 30
... RFsnd OSC RFPIX RFSND OSC - Measured in the evaluation board. OSC IF RFpix OSC KTS6027-2, KTS6029-2 Reference Test Conditions L Item min after switching kHz f = 367.25 MHz kHz f = 801.25 MHz 10kHz dBµV ...
Page 31
... Table 5-9 Charge pump current on page (see Table 5-8 Reference divider ratio on page bit = 0: enable V bit = 1: disable V bit = 0: NPN open-collector output is inactive bit = 1: NPN open-collector output is active (see Table 5-11 A/D converter levels on page bit = 1: loop is locked KTS6027-2, KTS6029-2 Reference bit2 bit1 LSB Ack MA1 MA0 0 ...
Page 32
... With a 4 MHz quartz. Wireless Components MA1 Mode 1). normal extended 1 KTS6027-2, KTS6029-2 Reference MA0 RSA RSB 2). fref kHz 0 1 31.25 kHz ...
Page 33
... KTS6027-2, KTS6029-2 Reference ...
Page 34
... Table 5-11 A/D converter levels Voltage at ADC (0...0.15)*V CC (0.15...0.3)*V CC (0.3...0.45)*V CC (0.45...0.6)*V CC (0.6...1)*V CC Wireless Components KTS6027-2, KTS6029 Reference Specification, July 2001 ...
Page 35
Start Addressing 1 MA1 MA0 R/W Telegram examples: Start-ADB-DB1-DB2-CB-BB-Stop Start-ADB-CB-BB-DB1-DB2-Stop Start-ADB-DB1-DB2-Stop Start-ADB-CB-BB-Stop Ack. 1st Byte Ack. 2nd Byte Ack. 3rd Byte Abbreviations: Start= start condition ADB= address byte DB1= prog. divider byte 1 DB2= prog. divider ...
Page 36
... test Set-up in HIGH V HIGHIN IFOUT Device Balun under V i 1:1 50 Test HIGHIN = dBµV meas = 20 log insertion loss of balun KTS6027-2, KTS6029-2 Reference 50 spectrum V o analyser GVHFM 50 spectrum V o analyser GUHFM Specification, July 2001 ...
Page 37
... MHz RF loss = 1.3 dB image suppression = 13 dB LOW/ IFOUT IN OUT MIDIN Device Matching Circuit under Test NF = NFmeas - loss of matching circuit (dB KTS6027-2, KTS6029-2 Reference 15p 1n Out 50 τ semi rigid cable 300 mm long 96 pF/m 33dB/100m 22p Noise Figure Meter NFVHFM Specification, July 2001 NFM ...
Page 38
... V meas RMS Votmeter LOW/ C IFOUT MIDIN Device under V i Test D => meas , V = 100 dBµV pix modulated with 1 kHz snd KTS6027-2, KTS6029-2 Reference Noise Figure Meter 18 dB attenuator 45.75 MHz 50 V modulation o analyser Specification, July 2001 NFUHFM XVHFM ...
Page 39
... AM modulated with 1 kHz snd and f ref div + 5 V Test Mode Counter PMID f ref PLOW Counter f div KTS6027-2, KTS6029-2 Reference 18 dB attenuator 45.75 MHz 50 V modulation o analyser XUHFM ref R: reference divider ratio VCO ...
Page 40
... Electrical Diagrams 5.5.1 Input admittance (S11) of the LOW/MID band mixer input Y = 20mS 0 5.5.2 Input impedance (S11) of the HIGH band mixer input Wireless Components (symmetrical) 855.25 MHz 415.25 MHz Rdiff KTS6027-2, KTS6029-2 Reference 0 48.25 MHz 407.25 MHz Y_VHFMIX Zn_UHFMIX Specification, July 2001 ...
Page 41
... Output admittance (S22) of the Mixer output Y = 20mS 0 5.5.4 Output impedance (S22) of the IF output Wireless Components KTS6027-2, KTS6029-2 0 45.75 MHz Reference Rdiff 0 45.75 MHz Y_MIXOUT UIFOUT Specification, July 2001 ...