X24C01 Xicor, X24C01 Datasheet
X24C01
Available stocks
Related parts for X24C01
X24C01 Summary of contents
Page 1
... X24C01 2 Serial E PROM DESCRIPTION The X24C01 is a CMOS 1024 bit serial E internally organized as 128 x 8. The X24C01 features a serial interface and software protocol allowing operation on a simple two wire bus. 2 Xicor E PROMs are designed and tested for applica- tions requiring extended endurance. Inherent data re- tention is greater than 100 years ...
Page 2
... 0.5 CC 3837 PGM T02 2 DIP PLASTIC X24C01 SCL SDA 3837 FHD F02 SOIC/MSOP X24C01 SCL SDA 3837 FHD F03 5V 2190 OUTPUT 100pF 3837 FHD F16 ...
Page 3
... The device controlling the transfer is a master and the device being controlled is the slave. The master will always initiate data transfers and provide the clock for both transmit and receive operations. There- fore, the X24C01 will be considered a slave in all applications. Figure 1. Data Validity SCL ...
Page 4
... R/W bit write operation has been selected, the X24C01 will respond with an acknowledge after each byte of data is received. In the read mode the X24C01 will transmit eight bits of data, release the SDA line and monitor the line for an acknowledge acknowledge is detected and no stop condition is generated by the master, the X24C01 will continue to transmit data ...
Page 5
... BUS ACTIVITY: S X24C01 B the page address. The X24C01 is capable of a four byte page write operation initiated in the same manner as the byte write operation, but instead of terminating the transfer of data after the first data byte, the master can transmit up to three more bytes. After the receipt of each data byte, the X24C01 will respond with an acknowledge ...
Page 6
... X24C01 initiates the internal write cycle. ACK polling can be initiated immediately. This involves issuing the start condition followed by the word address for a write operation. If the X24C01 is still busy with the write operation no ACK will be returned. If the X24C01 has completed the write operation an ACK will be returned and the controller can then proceed with the next read or write operation ...
Page 7
... At the end of the address space (address 127) the counter “rolls over” to zero and the X24C01 continues to output data for each acknowledge re- ceived. Refer to Figure 8 for the address, acknowledge and data transfer sequence ...
Page 8
... Exposure to absolute maximum rating condi- tions for extended periods may affect device reliability. Max. Supply Voltage 70 C X24C01 +85 C X24C01-3.5 +125 C X24C01-3 X24C01-2.7 Limits Min. Max 100 –1 ...
Page 9
... X24C01 A.C. CHARACTERISTICS (Over recommended operating conditions, unless otherwise specified) Read & Write Cycle Limits Symbol f SCL Clock Frequency SCL T Noise Suppression Time I Constant at SCL, SDA Inputs t SCL Low to SDA Data Out Valid AA t Time the Bus Must Be Free Before a BUF New Transmission Can Start ...
Page 10
... Write Cycle Time WR The write cycle time is the time from a valid stop condition of a write sequence to the end of the internal erase/program cycle. During the write cycle, the X24C01 Write Cycle Timing SCL SDA 8th BIT WORD n Notes: (5) Typical values are for and nominal supply voltage (5V) ...
Page 11
... X24C01 PACKAGING INFORMATION HALF SHOULDER WIDTH ON ALL END PINS OPTIONAL 0.015 (0.38) MAX. NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESES IN MILLIMETERS) 8-LEAD PLASTIC IN-LINE PACKAGE TYPE P 0.430 (10.92) 0.360 (9.14) 0.092 (2.34) DIA. NOM. PIN 1 INDEX PIN 1 0.300 (7.62) REF. SEATING PLANE 0.150 (3.81) 0.125 (3.18) 0.110 (2.79) 0.090 (2.29) 0.325 (8.25) 0.300 (7.62) TYP ...
Page 12
... X24C01 PACKAGING INFORMATION 8-LEAD PLASTIC SMALL OUTLINE GULL WING PACKAGE TYPE S PIN 1 INDEX NOTE: ALL DIMENSIONS IN INCHES (IN PARENTHESIS IN MILLIMETERS) PIN 1 0.014 (0.35) 0.019 (0.49) 0.188 (4.78) 0.197 (5.00) (4X) 7 0.050 (1.27) 0.010 (0.25 0.020 (0.50) 0 – 8 0.027 (0.683) 0.037 (0.937) 12 0.150 (3.80) 0.228 (5.80) 0.158 (4.00) 0.244 (6.20) 0.053 (1.35) 0.069 (1.75) 0.004 (0.19) ...
Page 13
... X24C01 PACKAGING INFORMATION 8-LEAD MINIATURE SMALL OUTLINE GULL WING PACKAGE TYPE M 0.012 + 0.006 / -0.002 (0.30 + 0.15 / -0.05) 0.040 0.002 (1.02 0.05) 0.007 (0.18) 0.005 (0.13) NOTE: 1. ALL DIMENSIONS IN INCHES AND (MILLIMETERS) 0.118 0.002 (3.00 0.05) 0.118 0.002 (3.00 0.05) 0.030 (0.76) 0.0216 (0.55) 7 TYP 0.036 (0.91) 0.032 (0.81) 0.008 (0.20) 0.004 (0.10) 0.150 (3.81) REF. 0.193 (4.90) REF. 13 0.0256 (0.65) TYP R 0 ...
Page 14
... Temperature Range Blank = Commercial = + Industrial = – + Military = – +125 C Package P = 8-Lead Plastic DIP S = 8-Lead SOIC M = 8-Lead MSOP X24C01 X Blank = 8-Lead SOIC P = 8-Lead Plastic DIP M = 8-Lead MSOP X Blank = 4.5V to 5.5V + 2.7V to 5.5V + 2.7V to 5.5V, – + 4.5V to 5.5V, – ...