IS27HC010-70W Integrated Silicon Solution, IS27HC010-70W Datasheet
IS27HC010-70W
Related parts for IS27HC010-70W
IS27HC010-70W Summary of contents
Page 1
... EP009-1F 07/18/97 DESCRIPTION ISSI The IS27HC010 is an ultra-high-speed 1 megabit (128K- word by 8-bit) Ultraviolet Erasable CMOS Programmable Read-Only Memory. It utilizes the standard JEDEC pinout making it functionally compatible with the IS27C010, but with significantly faster access capability. This superior random access capability results from a focused high-speed design. ...
Page 2
... IS27HC010 PIN CONFIGURATIONS 32-Pin DIP 32 VCC VPP 1 A16 2 31 PGM (P) A15 A12 4 29 A14 A13 A11 (G) 23 A10 ( DQ7 DQ0 13 20 DQ6 DQ1 14 19 DQ5 DQ2 15 18 ...
Page 3
... V = 5.25V. CC Program Inhibit Programming of multiple IS27HC010s in parallel with different data is also easily accomplished. Except for all like inputs of the parallel IS27HC010 may be common. A TTL low-level program pulse applied to an IS27HC010 CE input with V = 12.75 0.25V, PP HIGH will program that IS27HC010 ...
Page 4
... Either A1-A8 = A10-A16 = See DC Programming Characteristics for V 5. The IS27HC010 can use the same write algorithm during program as other IS27C010 or IS27010 devices. LOGIC SYMBOL 17 A0-A16 DQ0-DQ7 CE (E) PGM (P) OE (G) 4 System Applications During the switch between active and standby conditions, transient current peaks are produced on the rising and falling edges of Chip Enable ...
Page 5
... V . Manufacturer suggests to tie Caution: the IS27HC010 must not be removed from (or inserted into) a socket when V 3. Minimum DC input voltage is –0.5V. During transitions, the inputs may undershoot to –2.0V for periods less than 10 ns. Maximum DC voltage on output pins Tested under static DC conditions. ...
Page 6
... CCSB Current Notes must be applied simultaneously or before V CC below V . Manufacturer suggests to tie Caution: the IS27HC010 must not be removed from (or inserted into) a socket when tested with = V to simulate open outputs Maximum active power usage is the sum Minimum DC input voltage is – ...
Page 7
... This parameter is only sampled, not 100% tested. 3. Caution: The IS27HC010 must not be removed from (or inserted into) a socket or board when V 4. Output Load: 1 TTL gate and Input Rise and Fall times: 2 ns. Input Pulse Levels 3V. ...
Page 8
... must be V during the entire programming and verifying procedure When programming IS27HC010, a 0.1 F capacitor is required across V which may damage the device. 4. Programming characteristics are sampled but not 100% tested at worst-case conditions. 8 (1,2,3, + ...
Page 9
... IS27HC010 PROGRAMMING ALGORITHM WAVEFORM ADDRESS t AS DATA Vcc–0.3V t VPS 10% t VCS CE t CES PGM OE Notes: 1. The timing reference level is 1.5V for inputs and outputs 2. t and t are characteristics of the device but must be accommodated by the programmer. OE DFP Integrated Silicon Solution, Inc. ...
Page 10
... IS27HC010 PROGRAMMING FLOW CHART Interactive programming Section Verify Section 10 Address = First Location V Program One 100 µs Pulse Fail No Increment Address Vcc = V Device Passed Start Vcc = 6.25V = 12.75V Increment X Yes X = 25? No Verify Byte Pass Last Address? Yes = 5.25V PP Fail Verify All ...
Page 11
... IS27HC010 ORDERING INFORMATION Commercial Range +70 C Speed (ns) Order Part Number 30 IS27HC010-30W IS27HC010-30PL IS27HC010-30T 45 IS27HC010-45W IS27HC010-45PL IS27HC010-45T 70 IS27HC010-70W IS27HC010-70PL IS27HC010-70T ORDERING INFORMATION Industrial Range: – +85 C Speed (ns) Order Part Number 30 IS27HC010-30PLI IS27HC010-30TI 45 IS27HC010-45PLI IS27HC010-45TI 70 IS27HC010-70PLI IS27HC010-70TI Integrated Silicon Solution, Inc. ...