AT89LP51RC2 Atmel Corporation, AT89LP51RC2 Datasheet - Page 136
AT89LP51RC2
Manufacturer Part Number
AT89LP51RC2
Description
Manufacturer
Atmel Corporation
Specifications of AT89LP51RC2
Flash (kbytes)
32 Kbytes
Max. Operating Frequency
20 MHz
Cpu
8051-1C
Max I/o Pins
42
Spi
1
Twi (i2c)
1
Uart
1
Adc Channels
7
Adc Resolution (bits)
10
Adc Speed (ksps)
153.8
Sram (kbytes)
1.375
Self Program Memory
API
Operating Voltage (vcc)
2.4 to 5.5
Timers
4
Isp
SPI/OCD/UART
Watchdog
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 136 of 254
- Download datasheet (8Mb)
19.1.4
136
AT89LP51RB2/RC2/IC2 Preliminary
Data Packet Format
ter’s request, the SDA line should be left high in the ACK clock cycle. The Master can then
transmit a STOP condition, or a REPEATED START condition to initiate a new transmission. An
address packet consisting of a slave address and a READ or a WRITE bit is called SLA+R or
SLA+W, respectively.
The MSB of the address byte is transmitted first. Slave addresses can freely be allocated by the
designer, but the address 0000 000 is reserved for a general call.
When a general call is issued, all slaves should respond by pulling the SDA line low in the ACK
cycle. A general call is used when a Master wishes to transmit the same message to several
slaves in the system. When the general call address followed by a write bit is transmitted on the
bus, all slaves set up to acknowledge the general call will pull the SDA line low in the ACK cycle.
The following data packets will then be received by all the slaves that acknowledged the general
call. Note that transmitting the general call address followed by a Read bit is meaningless, as
this would cause contention if several slaves started transmitting different data.
All addresses of the format 1111 xxx should be reserved for future purposes.
Figure 19-4. Address Packet Format
All data packets transmitted on the TWI bus are nine bits long, consisting of one data byte and
an acknowledge bit. During a data transfer, the Master generates the clock and the START and
STOP conditions, while the Receiver is responsible for acknowledging the reception. An
Acknowledge (ACK) is signalled by the Receiver pulling the SDA line low during the ninth SCL
cycle. If the Receiver leaves the SDA line high, a NACK is signalled. When the Receiver has
received the last byte, or for some reason cannot receive any more bytes, it should inform the
Transmitter by sending a NACK after the final byte. The MSB of the data byte is transmitted first.
Figure 19-5. Data Packet Format
Transmitter
Aggregate
SDA from
SDA from
SCL from
Receiver
Master
SDA
SCL
SDA
SLA+R/W
START
Data MSB
Addr MSB
1
1
2
2
Data Byte
7
Data LSB
Addr LSB
8
7
ACK
9
R/W
8
ACK
STOP, REPEATED
9
START, or Next
Data Byte
3722A–MICRO–10/11
Related parts for AT89LP51RC2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
8-Bit Microcontroller with 4K Bytes Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: