ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 114
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 114 of 198
- Download datasheet (5Mb)
9.5.4
9.5.5
8111C–MCU Wireless–09/09
Bit
+0x11
Read/Write
Reset Value
Interrupt Handling
Register Description
7
R
0
Reserved
A supply voltage drop below the configured threshold value is indicated by an interrupt IRQ_7
(BAT_LOW), see
if BATMON_OK changes from 1 to 0.
No interrupt is generated when:
When the battery voltage is close to the programmed threshold voltage, noise or temporary volt-
age drops may generate unwanted interrupts. To avoid this:
Register 0x11 (BATMON):
This register configures the battery monitor to compare the supply voltage at pin 28 (EVDD) to
the threshold BATMON_VTH. Additionally the supply voltage status at pin 28 (EVDD) is accessi-
ble by reading register bit BATMON_OK according to the actual BATMON settings.
• Bit [7:6] - Reserved
• Bit 5 - BATMON_OK
The register bit BATMON_OK indicates the level of the external supply voltage with respect to
the programmed threshold BATMON_VTH.
Table 9-9.
• Bit 4 - BATMON_HR
BATMON_HR sets the range and resolution of the battery monitor.
Table 9-10.
Register Bit
BATMON_OK
Register Bit
BATMON_HR
• The battery voltage is under the default 1.8V threshold at power up
• A new threshold is set, which is still above the current supply voltage
• Disable the IRQ_7 (BAT_LOW) in register 0x0E (IRQ_MASK) and treat the battery as
• Set a lower threshold value.
6
R
0
(BATMON_OK was never 1), or
(BATMON_OK remains 0).
empty, or
BATMON_OK
5
R
0
Battery Monitor Status
Battery Monitor Range Selection
Section 6.6 “Interrupt Logic” on page
BATMON_HR
R/W
4
0
Value
Value
0
1
0
1
Description
The battery voltage is below the threshold.
The battery voltage is above the threshold.
Description
Enables the low range, see BATMON_VTH
Enables the high range, see BATMON_VTH
R/W
3
0
R/W
2
0
BATMON_VTH
29. Note that the interrupt is issued only
R/W
1
1
AT86RF231
R/W
0
0
BATMON
114
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika