ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 125
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 125 of 198
- Download datasheet (5Mb)
9.8
9.8.1
9.8.2
8111C–MCU Wireless–09/09
Bit
+0x18
Read/Write
Reset Value
Automatic Filter Tuning (FTN)
Overview
Register Description
FTN_START
R/W
7
0
The FTN is incorporated to compensate device tolerances for temperature, supply voltage varia-
tions as well as part-to-part variations of the radio transceiver. The filter-tuning result is used to
correct the analog baseband filter transfer function and the PLL loop-filter time constant, refer to
Section 4. “General Circuit Description” on page
An FTN calibration cycle is initiated automatically when entering the TRX_OFF state from the
SLEEP, RESET or P_ON states.
Although receiver and transmitter are very robust against these variations, it is recommended to
initiate the FTN manually if the radio transceiver does not use the SLEEP state. If necessary, a
calibration cycle is to be initiated in states TRX_OFF, PLL_ON or any receive state. This applies
in particular for the High Data Rate Modes with a much higher sensitivity against BPF transfer
function variations. The recommended calibration interval is 5 min or less.
Register 0x18 (FTN_CTRL):
This register controls the operation of the filter tuning network calibration loop.
• Bit 7 - FTN_START
FTN_START = 1 initiates the filter tuning network calibration. When the calibration cycle has fin-
ished after at most 25 µs the register bit is automatically reset to 0.
• Bit [6:0] - Reserved
R/W
6
1
R/W
5
0
R/W
4
1
Reserved
R/W
3
1
10.
R/W
2
0
R/W
1
0
AT86RF231
R/W
0
0
FTN_CTRL
125
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika