ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 56
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 56 of 198
- Download datasheet (5Mb)
8111C–MCU Wireless–09/09
The same holds for PAN coordinators, see
PAN-Coordinator
Table 7-7.
Promiscuous Mode
The promiscuous mode is described in IEEE 802.15.4-2006, section 7.5.6.2. This mode is fur-
ther illustrated in
mode, the MAC sub layer shall pass received frames with correct FCS to the next higher layer
and shall not be processed further. That implies that frames should never be acknowledged.
0x20,0x21
0x22,0x23
Register
Address
...........
0x24,
0x0C
0x2C
0x2B
0x2E
0x2E
0x2E
1.
2.
If a network should only allow access to nodes which use the IEEE 802.15.4-2003,
then AACK_FVN_MODE should be set to 0.
If a device should acknowledge all frames independent of its frame version,
AACK_FVN_MODE should be set to 3. However, this can result in conflicts with
co-existing IEEE 802.15.4-2006 standard compliant networks.
Register
Configuration of a PAN Coordinator
Bits
7:6
Figure 7-9 on page
7
0
3
5
Register Name
SHORT_ADDR_0/1
PAN_ADDR_0/1
IEEE_ADDR_0
........
IEEE_ADDR_7
RX_SAFE_MODE
SLOTTED_OPERATION
AACK_I_AM_COORD
AACK_SET_PD
AACK_FVN_MODE
53. According to IEEE 802.15.4-2006 when in promiscuous
Table 7-7 on page
Description
Set node addresses
0: disable frame protection
1: enable frame protection
0: if transceiver works in unslotted mode
1: if transceiver works in slotted mode
1: device is PAN coordinator
0: frame pending subfield is not set in FC
1: frame pending subfield is set in FCF
Controls the ACK behavior, depending on FCF
frame version number
0x00: acknowledges only frames with version
number 0, i.e. according to IEEE 802.15.4-2003
frames
0x01: acknowledges only frames with version
number 0 or 1, i.e. frames according to IEEE
802.15.4-2006
0x10: acknowledges only frames with version
number 0 or 1 or 2
0x11: acknowledges all frames, independent of
the FCF frame version number
56.
AT86RF231
56
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika