ATmega1284PR231 Atmel Corporation, ATmega1284PR231 Datasheet - Page 99
ATmega1284PR231
Manufacturer Part Number
ATmega1284PR231
Description
Manufacturer
Atmel Corporation
Datasheets
1.AT86RF231.pdf
(198 pages)
2.ATMEGA1284PR231.pdf
(380 pages)
3.ATMEGA1284PR231.pdf
(20 pages)
Specifications of ATmega1284PR231
Flash (kbytes)
128 Kbytes
Max. Operating Frequency
20 MHz
Max I/o Pins
32
Spi
3
Twi (i2c)
1
Uart
2
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Crypto Engine
AES
Sram (kbytes)
16
Eeprom (bytes)
4096
Operating Voltage (vcc)
1.8 to 3.6
Timers
3
Frequency Band
2.4 GHz
Max Data Rate (mb/s)
2
Antenna Diversity
Yes
External Pa Control
Yes
Power Output (dbm)
3
Receiver Sensitivity (dbm)
-101
Receive Current Consumption (ma)
13.2
Transmit Current Consumption (ma)
14.4
Link Budget (dbm)
104
- Current page: 99 of 198
- Download datasheet (5Mb)
8.6
8.6.1
8111C–MCU Wireless–09/09
Link Quality Indication (LQI)
Overview
According to IEEE 802.15.4, the LQI measurement is a characterization of the strength and/or
quality of a received packet. The measurement may be implemented using receiver ED, a sig-
nal-to-noise ratio estimation, or a combination of these methods. The use of the LQI result by the
network or application layers is not specified in this standard. LQI values shall be an integer
ranging from 0x00 to 0xFF. The minimum and maximum LQI values (0x00 and 0xFF) should be
associated with the lowest and highest quality compliant signals, respectively, and LQI values in
between should be uniformly distributed between these two limits.
The LQI measurement of the AT86RF231 is implemented as a measure of the link quality which
can be described with the packet error rate (PER) for this link. An LQI value can be associated
with an expected packet error rate. The PER is the ratio of erroneous received frames to the
total number of received frames. A PER of zero indicates no frame error, whereas at a PER of
one no frame was received correctly.
The radio transceiver uses correlation results of multiple symbols within a frame to determine
the LQI value. This is done for each received frame. The minimum frame length for a valid LQI
value is two octets PSDU. LQI values are integers ranging from 0 to 255.
As an example,
tain LQI value.
Figure 8-6.
The values are taken from received frames of PSDU length of 20 octets on transmission chan-
nels with reasonable low multipath delay spreads. If the transmission channel characteristic has
higher multipath delay spread than assumed in the example, the PER is slightly higher for a cer-
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1
0
Conditional Packet Error Rate versus LQI
Figure 8-6 on page 99
50
100
LQI
shows the conditional packet error when receiving a cer-
150
200
250
AT86RF231
99
Related parts for ATmega1284PR231
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Microcontroller with 128K bytes In-system programmable flash, 8 MHz, power supply =2.7 - 5.5V
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
8-bit Microcontroller with 128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
IC AVR MCU 2.4GHZ XCEIVER 64QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA644/AT86RF230 40-DIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 QFN
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
BUNDLE ATMEGA644P/AT86RF230 TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU ATMEGA1281/AT86RF230 64-TQFP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
MCU, 8BIT, AVR, 16K FLASH, 28PDIP
Manufacturer:
Atmel
Datasheet:
Part Number:
Description:
Microcontroller Modules MCU CARD BIGAVR6 100P W/ ATMEGA2560
Manufacturer:
mikroElektronika