ATmega16M1 Automotive Atmel Corporation, ATmega16M1 Automotive Datasheet - Page 5

• Manufacturer Part Number: ATmega16M1 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega16M1 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.3.5
7701E–AVR–02/11
Pin Descriptions
VCC
GND
Port B (PB3...PB0)
RESET
Port A (PA7...PA0)
Supply voltage.
Ground.
Port B is a 4-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port B output buffers have symmetrical drive characteristics with both high sink and source
capability except PB3, which has the RESET capability. To use pin PB3 as an I/O pin instead
of RESET pin, program (‘0’) RSTDISBL fuse. As inputs, Port B pins that are externally pulled
low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when
a reset condition becomes active, even if the clock is not running.
Port B also serves the functions of various special features of the Atmel
listed on
Reset input. A low level on this pin for longer than the minimum pulse length will generate a
reset, even if the clock is not running. The minimum pulse length is given in
42. Shorter pulses are not guaranteed to generate a reset.
Port A is a 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The
Port A output buffers have symmetrical drive characteristics with both high sink and source
capability. As inputs, Port A pins that are externally pulled low will source current if the pull-up
resistors are activated. The Port A pins are tri-stated when a reset condition becomes active,
even if the clock is not running.
Port A has an alternate function as analog input for the ADC, analog comparator, timer/coun-
ter, SPI and pin change interrupt as described in
page
61.
Section 12.3 “Alternate Port Functions” on page
Atmel ATtiny24/44/84 [Preliminary]
Section 12.3 “Alternate Port Functions” on
61.
®
ATtiny24/44/84 as
Table 9-1 on page
5