ATmega16M1 Automotive Atmel Corporation, ATmega16M1 Automotive Datasheet - Page 89

• Manufacturer Part Number: ATmega16M1 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega16M1 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 27
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Can: 1
• Lin: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 14
• Input Capture Channels: 1
• Pwm Channels: 10
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

13.9.6
13.9.7
7701E–AVR–02/11
TIMSK0 – Timer/Counter 0 Interrupt Mask Register
TIFR0 – Timer/Counter 0 Interrupt Flag Register
• Bits 7..3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny24/44/84 and will always read as zero.
• Bit 2- OCIE0B: Timer/Counter 0 Output Compare Match B Interrupt Enable
When the OCIE0B bit is written to one, and the I-bit in the status register is set, the timer/coun-
ter 0 compare match B interrupt is enabled. The corresponding interrupt is executed if a
compare match in timer/counter occurs, i.e., when the OCF0B bit is set in the timer/counter 0
interrupt flag register (TIFR0).
• Bit 1– OCIE0A: Timer/Counter0 Output Compare Match A Interrupt Enable
When the OCIE0A bit is written to one, and the I-bit in the status register is set, the timer/coun-
ter 0 compare match A interrupt is enabled. The corresponding interrupt is executed if a
compare match in timer/counter 0 occurs, i.e., when the OCF0A bit is set in the timer/counter
0 interrupt flag register (TIFR0).
• Bit 0– TOIE0: Timer/Counter0 Overflow Interrupt Enable
When the TOIE0 bit is written to one, and the I-bit in the status register is set, the timer/counter
0 overflow interrupt is enabled. The corresponding interrupt is executed if an overflow in
timer/counter 0 occurs, i.e., when the TOV0 bit is set in the timer/counter 0 interrupt flag regis-
ter (TIFR0).
• Bits 7..3 – Res: Reserved Bits
These bits are reserved bits in the ATtiny24/44/84 and will always read as zero.
• Bit 2– OCF0B: Output Compare Flag 0 B
The OCF0B bit is set when a compare match occurs between the timer/counter 0 and the data
in OCR0B, the output compare register 0 B. OCF0B is cleared by hardware when executing
the corresponding interrupt handling vector. Alternatively, OCF0B is cleared by writing a logi-
cal one to the flag. When the I-bit in SREG, OCIE0B (timer/counter compare b match interrupt
enable), and OCF0B are set, the timer/counter compare match interrupt is executed.
• Bit 1– OCF0A: Output Compare Flag 0 A
The OCF0A bit is set when a compare match occurs between the timer/counter 0 and the data
in OCR0A, the output compare register 0 A. OCF0A is cleared by hardware when executing
the corresponding interrupt handling vector. Alternatively, OCF0A is cleared by writing a logi-
cal one to the flag. When the I-bit in SREG, OCIE0A (timer/counter 0 compare match interrupt
enable), and OCF0A are set, the timer/counter 0 compare match interrupt is executed.
Bit
0x39 (0x59)
Read/Write
Initial Value
Bit
0x38 (0x58)
Read/Write
Initial Value
R
R
7
–
0
7
–
0
R
6
–
0
R
6
–
0
Atmel ATtiny24/44/84 [Preliminary]
R
5
–
0
R
5
–
0
R
4
–
0
R
4
–
0
R
3
–
0
R
3
–
0
OCIE0B
OCF0B
R/W
R/W
2
0
2
0
OCIE0A
OCF0A
R/W
R/W
1
0
1
0
TOIE0
TOV0
R/W
R/W
0
0
0
0
TIMSK0
TIFR0
89