ATmega48 Atmel Corporation, ATmega48 Datasheet - Page 29

no-image

ATmega48

Manufacturer Part Number
ATmega48
Description
Manufacturer
Atmel Corporation
Datasheets

Specifications of ATmega48

Flash (kbytes)
4 Kbytes
Pin Count
32
Max. Operating Frequency
20 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
23
Ext Interrupts
24
Usb Speed
No
Usb Interface
No
Spi
2
Twi (i2c)
1
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
15
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.5
Eeprom (bytes)
256
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
3
Output Compare Channels
6
Input Capture Channels
1
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ATmega48-10AU
Manufacturer:
FEVA
Quantity:
30 000
Part Number:
ATmega48-15AT
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega48-15AT1
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega48-15AT1
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega48-15AZ
Manufacturer:
ATMEL
Quantity:
3 500
Part Number:
ATmega48-15AZ
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega48-15AZ
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega48-15AZV
Manufacturer:
MICROCHIP
Quantity:
3 100
Part Number:
ATmega48-15AZV
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega48-20AI
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
ATmega48-20AU
Manufacturer:
ATMEL
Quantity:
6 460
Part Number:
ATmega48-20AU
Manufacturer:
Atmel
Quantity:
1 300
Part Number:
ATmega48-20AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
ATmega48-20AU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
1 753
Company:
Part Number:
ATmega48-20AU
Quantity:
2 500
ATmega48/88/168
- Two succeeding resets are applied where the second reset occurs in the 10ns window
before the device is out of the reset-state caused by the first reset.
- A reset is applied in a 10ns window while the system clock prescaler value is updated by
software.
- Leaving SPI-programming mode generates an internal reset signal that can trigger this
case.
The two first cases can occur during normal operating mode, while the last case occurs only
during programming of the device.
Problem fix/workaround
The first case can be avoided during run-mode by ensuring that only one reset source is
active. If an external reset push button is used, the reset start-up time should be selected
such that the reset line is fully debounced during the start-up time.
The second case can be avoided by not using the system clock prescaler.
The third case occurs during In-System programming only. It is most frequently seen when
using the internal RC at maximum frequency.
If the device gets stuck in the reset-state, turn power off, then on again to get the device out
of this state.
2. Interrupts may be lost when writing the timer registers in the asynchronous timer
The interrupt will be lost if a timer register that is synchronous timer clock is written when the
asynchronous Timer/Counter register (TCNTx) is 0x00.
Problem fix/workaround
Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor
0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous
Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx).
29
2545TS–AVR–05/11

Related parts for ATmega48