ATmega48PA Atmel Corporation, ATmega48PA Datasheet - Page 264

• Manufacturer Part Number: ATmega48PA
• Manufacturer: Atmel Corporation

Specifications of ATmega48PA

• Flash (kbytes): 4 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.5
• Eeprom (bytes): 256
• Self Program Memory: NO
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

24.9
24.9.1
8271D–AVR–05/11
Register Description
ADMUX – ADC Multiplexer Selection Register
• Bit 7:6 – REFS[1:0]: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in
changed during a conversion, the change will not go in effect until this conversion is complete
(ADIF in ADCSRA is set). The internal voltage reference options may not be used if an external
reference voltage is being applied to the AREF pin.
Table 24-3.
• Bit 5 – ADLAR: ADC Left Adjust Result
The ADLAR bit affects the presentation of the ADC conversion result in the ADC Data Register.
Write one to ADLAR to left adjust the result. Otherwise, the result is right adjusted. Changing the
ADLAR bit will affect the ADC Data Register immediately, regardless of any ongoing conver-
sions. For a complete description of this bit, see
page
• Bit 4 – Reserved
This bit is an unused bit in the ATmega48A/PA/88A/PA/168A/PA/328/P, and will always read as
zero.
• Bits 3:0 – MUX[3:0]: Analog Channel Selection Bits
The value of these bits selects which analog inputs are connected to the ADC. See
for details. If these bits are changed during a conversion, the change will not go in effect until this
conversion is complete (ADIF in ADCSRA is set).
Bit
(0x7C)
Read/Write
Initial Value
REFS1
0
0
1
1
267.
REFS0
REFS1
Voltage Reference Selections for ADC
R/W
0
1
0
1
7
0
ATmega48A/PA/88A/PA/168A/PA/328/P
REFS0
Voltage Reference Selection
AREF, Internal V
AV
Reserved
Internal 1.1V Voltage Reference with external capacitor at AREF pin
R/W
6
0
CC
with external capacitor at AREF pin
ADLAR
R/W
5
0
ref
turned off
R
4
–
0
MUX3
R/W
”ADCL and ADCH – The ADC Data Register” on
3
0
MUX2
R/W
2
0
MUX1
R/W
1
0
Table
MUX0
R/W
0
0
24-3. If these bits are
ADMUX
Table 24-4
264