ATtiny4 Atmel Corporation, ATtiny4 Datasheet - Page 111
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATtiny4
Manufacturer Part Number
ATtiny4
Description
Manufacturer
Atmel Corporation
Specifications of ATtiny4
Flash (kbytes)
0.5 Kbytes
Pin Count
6
Max. Operating Frequency
12 MHz
Cpu
8-bit AVR
# Of Touch Channels
1
Hardware Qtouch Acquisition
No
Max I/o Pins
4
Ext Interrupts
4
Usb Speed
No
Usb Interface
No
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
0.03
Self Program Memory
NO
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 125
I/o Supply Class
1.8 to 5.5
Operating Voltage (vcc)
1.8 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
1
Output Compare Channels
2
Input Capture Channels
1
Pwm Channels
2
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ATtiny4-TS8R
Manufacturer:
ADI
Quantity:
635
Part Number:
ATtiny4-TSHR
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny4313-MMHR
Manufacturer:
MICRON
Quantity:
4 100
Company:
Part Number:
ATtiny4313-MU
Manufacturer:
HITTITE
Quantity:
101
Part Number:
ATtiny4313-SU
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny44-15MZ
Manufacturer:
ATMEL
Quantity:
1 000
Part Number:
ATtiny44-15MZ
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Company:
Part Number:
ATtiny44-15SSZ
Manufacturer:
ATMEL
Quantity:
350
Part Number:
ATtiny441-MUR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Part Number:
ATtiny44A-MFR
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
15.3.3.1
15.3.4
15.3.5
8127E–AVR–11/11
Signature Section
Calibration Section
Latching of Configuration Bits
Configuration bits are not affected by a chip erase but they can be cleared using the configura-
tion section erase command (see
configuration bits are locked if Non-Volatile Lock Bit 1 (NVLB1) is programmed.
All configuration bits are latched either when the device is reset or when the device exits the
external programming mode. Changes to configuration bit values have no effect until the device
leaves the external programming mode.
The signature section is a dedicated memory area used for storing miscellaneous device infor-
mation, such as the device signature. Most of this memory section is reserved for internal use,
as shown in
Table 15-7.
ATtiny4/5/9/10 have a three-byte signature code, which can be used to identify the device. The
three bytes reside in the signature section, as shown in
ATtiny4/5/9/10 is given in
Table 15-8.
ATtiny4/5/9/10 have one calibration byte. The calibration byte contains the calibration data for
the internal oscillator and resides in the calibration section, as shown in
reset, the calibration byte is automatically written into the OSCCAL register to ensure correct fre-
quency of the calibrated internal oscillator.
Table 15-9.
Signature word address
0x00
0x01
0x02 ... 0x0F
Part
ATtiny4
ATtiny5
ATtiny9
ATtiny10
Calibration word address
0x00
0x01 ... 0x07
Table
Signature bytes
Signature codes
Calibration byte
15-7.
Table
Manufacturer ID
15-8.
High byte
Device ID 1
Reserved for internal use
Reserved for internal use
Calibration word data
High byte
Reserved
Reserved
0x1E
0x1E
0x1E
0x1E
“Erasing the Configuration Section” on page
Signature Bytes
Signature word data
Device ID 1
0x8F
0x8F
0x90
0x90
Table
Low byte
Internal oscillator calibration value
Reserved
Manufacturer ID
Reserved for internal use
Low byte
Device ID 2
15-7. The signature data for
ATtiny4/5/9/10
Table
Device ID 2
114). Note that
0x0A
0x09
0x08
0x03
15-9. During
111