ATxmega64B3 Atmel Corporation, ATxmega64B3 Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATxmega64B3
Manufacturer Part Number
ATxmega64B3
Description
Manufacturer
Atmel Corporation
Specifications of ATxmega64B3
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
32 MHz
Cpu
8-bit AVR
# Of Touch Channels
16
Hardware Qtouch Acquisition
No
Max I/o Pins
36
Ext Interrupts
36
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Twi (i2c)
1
Uart
1
Segment Lcd
100
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
12
Adc Speed (ksps)
2000
Analog Comparators
2
Resistive Touch Screen
No
Temp. Sensor
Yes
Crypto Engine
AES/DES
Sram (kbytes)
4
Eeprom (bytes)
2048
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
Yes
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.6 to 3.6
Operating Voltage (vcc)
1.6 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
6
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 9 of 425
- Download datasheet (7Mb)
3.7
3.8
8291A–AVR–10/11
Status Register
Stack and Stack Pointer
Figure 3-3 on page 9
cycle, an ALU operation using two register operands is executed and the result is stored back to
the destination register.
Figure 3-3.
The status register (SREG) contains information about the result of the most recently executed
arithmetic or logic instruction. This information can be used for altering program flow in order to
perform conditional operations. Note that the status register is updated after all ALU operations,
as specified in the instruction set reference. This will in many cases remove the need for using
the dedicated compare instructions, resulting in faster and more compact code.
The status register is not automatically stored when entering an interrupt routine nor restored
when returning from an interrupt. This must be handled by software.
The status register is accessible in the I/O memory space.
The stack is used for storing return addresses after interrupts and subroutine calls. It can also be
used for storing temporary data. The stack pointer (SP) register always points to the top of the
stack. It is implemented as two 8-bit registers that are accessible in the I/O memory space. Data
are pushed and popped from the stack using the PUSH and POP instructions. The stack grows
from a higher memory location to a lower memory location. This implies that pushing data onto
the stack decreases the SP, and popping data off the stack increases the SP. The SP is auto-
matically loaded after reset, and the initial value is the highest address of the internal SRAM. If
the SP is changed, it must be set to point above address 0x2000, and it must be defined before
any subroutine calls are executed or before interrupts are enabled.
During interrupts or subroutine calls, the return address is automatically pushed on the stack.
The return address can be two or three bytes, depending on program memory size of the device.
For devices with 128KB or less of program memory, the return address is two bytes, and hence
the stack pointer is decremented/incremented by two. For devices with more than 128KB of pro-
gram memory, the return address is three bytes, and hence the SP is decremented/incremented
by three. The return address is popped off the stack when returning from interrupts using the
RETI instruction, and from subroutine calls using the RET instruction.
Register Operands Fetch
ALU Operation Execute
Total Execution Time
Result Write Back
Single Cycle ALU Operation
shows the internal timing concept for the register file. In a single clock
clk
CPU
T1
Atmel AVR XMEGA B
T2
T3
T4
9
Related parts for ATxmega64B3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
![U6046B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: