SAM3S1A Atmel Corporation, SAM3S1A Datasheet - Page 640

• Manufacturer Part Number: SAM3S1A
• Manufacturer: Atmel Corporation

Specifications of SAM3S1A

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 2
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

31.10.5.5
Figure 31-30. Repeated Start + Reversal from Read to Write Mode
Figure 31-31. Repeated Start + Reversal from Write to Read Mode
Notes:
640
TWI_RHR
TWI_RHR
TWI_THR
TWI_THR
TXCOMP
TXCOMP
EOSACC
EOSACC
SVREAD
SVREAD
Reversal of Read to Write
Reversal of Write to Read
RXRDY
SVACC
RXRDY
SVACC
TXRDY
TXRDY
TWD
TWD
1. In this case, if TWI_THR has not been written at the end of the read command, the clock is automatically stretched before
2. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is detected again.
SAM3S
the ACK.
Reversal after a Repeated Start
S
S
As soon as a START is detected
As soon as a START is detected
SADR
SADR
The master initiates the communication by a read command and finishes it by a write command.
Figure 31-30 on page 640
1. TXCOMP is only set at the end of the transmission because after the repeated start, SADR is detected again.
The master initiates the communication by a write command and finishes it by a read com-
mand.Figure 31-31 on page 640
mode.
W
R
Read TWI_RHR
A
A
DATA0
DATA0
DATA0
A
A
DATA0
DATA1
DATA1
DATA1
describes the repeated start + reversal from Read to Write mode.
NA
A
describes the repeated start + reversal from Write to Read
DATA1
Sr
Sr
SADR
SADR
Cleared after read
Cleared after read
R
W
DATA2
A
A
DATA2
DATA2
DATA2
A
A
DATA3
DATA3
DATA3
6500C–ATARM–8-Feb-11
DATA3
NA
A
P
P