SAM3S1A Atmel Corporation, SAM3S1A Datasheet - Page 861

• Manufacturer Part Number: SAM3S1A
• Manufacturer: Atmel Corporation

Specifications of SAM3S1A

• Flash (kbytes): 64 Kbytes
• Pin Count: 48
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 17
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Twi (i2c): 2
• Uart: 3
• Ssc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Figure 36-10. Method 1 (UPDM = 0)
6500C–ATARM–8-Feb-11
Method 1: Manual write of duty-cycle values and manual trigger of the update
UPDULOCK
CDTYUPD
CCNT0
CDTY
0x20
0x20
In this mode, the update of the period value, the duty-cycle values and the dead-time values
must be done by writing in their respective update registers with the CPU (respectively
PWM_CPRDUPDx, PWM_CDTYUPDx and PWM_DTUPDx).
To trigger the update, the user must use the bit UPDULOCK of the
Update Control Register”
PWM period) the synchronous channels:
After writing the UPDULOCK bit to 1, it is held at this value until the update occurs, then it is read
0.
Sequence for Method 1:
• If the bit UPDULOCK is set to 1, the update is done at the next PWM period of the
• If the UPDULOCK bit is not set to 1, the update is locked and cannot be performed.
1. Select the manual write of duty-cycle values and the manual update by setting the
2. Define the synchronous channels by the SYNCx bits in the PWM_SCM register.
3. Enable the synchronous channels by writing CHID0 in the PWM_ENA register.
4. If an update of the period value and/or the duty-cycle values and/or the dead-time val-
5. Set UPDULOCK to 1 in PWM_SCUC.
6. The update of the registers will occur at the beginning of the next PWM period. At this
synchronous channels.
UPDM field to 0 in the PWM_SCM register
ues is required, write registers that need to be updated (PWM_CPRDUPDx,
PWM_CDTYUPDx and PWM_DTUPDx).
moment the UPDULOCK bit is reset, go to
0x40
0x40
0x60
(PWM_SCUC) which allows to update synchronously (at the same
0x60
Step
4.) for new values.
“PWM Sync Channels
SAM3S
861