SAM3S1B Atmel Corporation, SAM3S1B Datasheet - Page 199

• Manufacturer Part Number: SAM3S1B
• Manufacturer: Atmel Corporation

Specifications of SAM3S1B

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

10.23.2
• PRIVDEFENA
Enables privileged software access to the default memory map:
0 = If the MPU is enabled, disables use of the default memory map. Any memory access to a location not covered by any
enabled region causes a fault.
1 = If the MPU is enabled, enables use of the default memory map as a background region for privileged software
accesses.
When enabled, the background region acts as if it is region number -1. Any region that is defined and enabled has priority
over this default map.
If the MPU is disabled, the processor ignores this bit.
• HFNMIENA
Enables the operation of MPU during hard fault, NMI, and FAULTMASK handlers.
When the MPU is enabled:
0 = MPU is disabled during hard fault, NMI, and FAULTMASK handlers, regardless of the value of the ENABLE bit
1 = the MPU is enabled during hard fault, NMI, and FAULTMASK handlers.
When the MPU is disabled, if this bit is set to 1 the behavior is Unpredictable.
• ENABLE
Enables the MPU:
0 = MPU disabled
1 = MPU enabled.
When ENABLE and PRIVDEFENA are both set to 1:
For privileged accesses, the default memory map is as described in
software that does not address an enabled memory region behaves as defined by the default memory map.
6500C–ATARM–8-Feb-11
31
23
15
7
MPU Control Register
30
22
14
6
The MPU CTRL register:
See the register summary in
assignments are:
• enables the MPU
• enables the default memory map background region
• enables use of the MPU when in the hard fault, Non-maskable Interrupt (NMI), and
FAULTMASK escalated handlers.
Reserved
29
21
13
5
28
20
12
4
Table 10-35 on page 197
Reserved
Reserved
Reserved
27
19
11
“Memory model” on page
3
PRIVDEFENA
26
18
10
2
for the MPU CTRL attributes. The bit
54. Any access by privileged
HFNMIENA
25
17
9
1
SAM3S
ENABLE
24
16
8
0
199