SAM3S1B Atmel Corporation, SAM3S1B Datasheet - Page 301

• Manufacturer Part Number: SAM3S1B
• Manufacturer: Atmel Corporation

Specifications of SAM3S1B

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 64 MHz
• Cpu: Cortex-M3
• # Of Touch Channels: 23
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 34
• Ext Interrupts: 34
• Usb Transceiver: 1
• Quadrature Decoder Channels: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 3
• Twi (i2c): 2
• Uart: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 10
• Adc Resolution (bits): 12
• Adc Speed (ksps): 1000
• Analog Comparators: 1
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 16
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8/3.3
• Operating Voltage (vcc): 1.62 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 3
• Output Compare Channels: 3
• Input Capture Channels: 3
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

18.3.3.7
18.3.3.8
6500C–ATARM–8-Feb-11
Security Bit Protection
Unique Identifier
The 4/8/12 MHz Fast RC oscillator is calibrated in production. This calibration can be read
through the Get CALIB Bit command. The table below shows the bit implementation for each
frequency:
The RC calibration for 4 MHz is set to 1,000,000.
When the security is enabled, access to the Flash, either through the JTAG/SWD interface or
through the Fast Flash Programming Interface, is forbidden. This ensures the confidentiality of
the code programmed in the Flash.
The security bit is GPNVM0.
Disabling the security bit can only be achieved by asserting the ERASE pin at 1, and after a full
Flash erase is performed. When the security bit is deactivated, all accesses to the Flash are
permitted.
Each part is programmed with a 128-bit Unique Identifier. It can be used to generate keys for
example.
To read the Unique Identifier the sequence is:
Note that during the sequence, the software can not run out of Flash (or the second plane in
case of dual plane).
RC Calibration Frequency
8 MHz output
12 MHz output
• Send the Start Read unique Identifier command (STUI) by writing the Flash Command
• When the Unique Identifier is ready to be read, the FRDY bit in the Flash Programming
• The Unique Identifier is located in the first 128 bits of the Flash memory mapping. So, at the
• To stop the Unique Identifier mode, the user needs to send the Stop Read unique Identifier
• When the Stop read Unique Identifier command (SPUI) has been performed, the FRDY bit in
Register with the STUI command.
Status Register (EEFC_FSR) falls.
address
command (SPUI) by writing the Flash Command Register with the SPUI command.
the Flash Programming Status Register (EEFC_FSR) rises. If an interrupt was enabled by
setting the FRDY bit in EEFC_FMR, the interrupt line of the NVIC is activated.
0x80000-0x8000F
.
EEFC_FRR Bits
[28 - 22]
[38 - 32]
SAM3S
301